Answer / d4rkhowl

I&C = Instrumentation and Control, Instrumenation field
dealing mainly with control systems such as PLC and DCS,
Programming, Etc.

I&E = Instrumentation and Electronics/Electrical,
Instrumentation field dealing mainly with field instruments
and their installation and maintenance.

Answer / rajkumar

probably you will be called as I&C Engr or C&I Engr in future

Answer / renjith

In all companies we use INST as short for instrumentation.

Answer / sivakumari

The short form of the INSTRUMENTATION is IN

Answer / visakh v

E&I tats how we had it...

Answer / aravind

INSTRUMENTATION IS THE FIELD OF SCIENCE THAT DEALS WITH
MEASURING AND CONTROLLING THE PHYSICAL PARAMETERS LIKE
TEMPERATURE ,LEVEL PRESSURE AND FLOW IT IS AN FORM OF
METROLOGICAL ENGINEERING ALSO

Answer / mansour

INSTRUMENTATION IS MEASURE AND CONTROL THE PARAMETERS LIKE
TEMP. PRESSURE LEVEL AND FLOW.

Answer / md abdullah

short form of Instrumentation=Inst

Answer / karthikeyan.

Ine- instrumentation engineering
E

Answer / ripul

instru.....
simply..

What is the relationship between the universal gravitational constant (G) and the acceleration due to gravity (g)?

3 Answers   APPSC,

I saw one P&ID 6" control valve has been connected with 8" process line, and 2" valve also connected in parallel with 6" valve. why the 2" valve connected in parallel, Is there any technical reason. please clarify. With Regards-Kittu

5 Answers   GNFC,

What should be the ideal tapping location for pressure differential transmitter for liquid service. If the tapping taken from the top of the pipe then PDIT will work properly or not. If PDIT do not work properly then what minimum corrective action should be taken in order to solve wrong tapping locations.

1 Answers  

We have yokogawa cs3000 one fcs and 4 his. After download to his, showing successfully at es, but not transferred to his.

1 Answers   Shyam Steel,

what is piezoelectric transducer?give an example in power plant n state its principle?

0 Answers   Jindal,

how to wire from pressure transmitter to marshalling panel and panel to controller and controller to dcs plz give the answer with example .

2 Answers  

in a power plant main steam flow is volumetric or mass flow? is it required compensation?

1 Answers   Wartsila,

HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME... SUPPOSE ,, I HAVE A CLOSE VESSELE TANK ( HEXANE MEDIA ) ,, I M USING ROSEMOUNT 2051 DPT FOR LEVEL APPLICATION .. ITS CALIBRATE RANGE IS.. . 0 TO 950 MMH20 ..I DID CALIBRATED DPT WITHOUT REMOVING IMPULSE LINE OF HIGH AND LOW TAPPING.. & WITHOUT DISTURB 3 WAY MANIFOLD..!!! BUT ,,, DURING CALIBRATION I SELECT RANGE BY HART LRV IS 900 MMH20 & URV IS 1300 MMH20 ,, BUT ,TANK LEVEL SOMETIMES 100 % AT 1100 MMH20 , SOMETIMES 1300 MMH20 ..IN THIS CONDITION .. WHOLE LOOP FAILED ,, MAIN THING IS THAT ,, HOW TO CUSTOME RANGE SELECT ?? AND IF I USED RANGE OVER THE ORIGINAL CALIBRATE RANGE ,,,THEN WHAT ERROR WILL BE COME ??? HOW TO ZERO CALIBRATION OF DPT... HOW TO ZERO TRIM BY MANIFOLD ?? AND FOR TANK LEVEL PURPOSE ... WHICH UNIT I CAN USE ??? IS THERE ANY CALCULATION OR CALIBRATION .. IF YEH .. THEN PLZ JUST GIVE ME CALIBRATION STEPS FOR DPT.. THANKS YOURSSSSSSS

1 Answers   Torrent Pharma,

what is the difference between active and passive loop ?

8 Answers  

In E&I diagram what is the meaning of rectangular box and circular box

3 Answers   L&T,

Why we use DPT? can we use PT instead of DPT?

2 Answers  

what is interface level and how it is calibrate?

0 Answers