HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME... SUPPOS

HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME...

SUPPOSE ,, I HAVE A CLOSE VESSELE TANK ( HEXANE MEDIA ) ,,

I M USING ROSEMOUNT 2051 DPT FOR LEVEL APPLICATION ..

ITS CALIBRATE RANGE IS.. . 0 TO 950 MMH20 ..I DID CALIBRATED DPT WITHOUT
REMOVING IMPULSE LINE OF HIGH AND LOW TAPPING.. & WITHOUT DISTURB 3 WAY
MANIFOLD..!!!

BUT ,,, DURING CALIBRATION I SELECT RANGE BY HART LRV IS 900 MMH20 & URV
IS 1300 MMH20 ,, BUT ,TANK LEVEL SOMETIMES 100 % AT 1100 MMH20 ,
SOMETIMES 1300 MMH20 ..IN THIS CONDITION .. WHOLE LOOP FAILED ,, MAIN
THING IS THAT ,, HOW TO CUSTOME RANGE SELECT ?? AND IF I USED RANGE OVER
THE ORIGINAL CALIBRATE RANGE ,,,THEN WHAT ERROR WILL BE COME ??? HOW TO
ZERO CALIBRATION OF DPT... HOW TO ZERO TRIM BY MANIFOLD ?? AND FOR TANK
LEVEL PURPOSE ... WHICH UNIT I CAN USE ??? IS THERE ANY CALCULATION OR
CALIBRATION .. IF YEH .. THEN PLZ JUST GIVE ME CALIBRATION STEPS FOR DPT..

THANKS YOURSSSSSSS

Question Posted / h0tchess0r

1 Answers
4529 Views
Torrent Pharma, I also Faced
E-Mail Answers

HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME... SUPPOSE ,, I HAVE A CLOSE ..

Answer / carl_ellis

There is insufficient information to determine what the
correct range of the transmitter should be.

1) Is there a capillary with remote seal on either side of
the DP xmtr? If so describe in detail.

2) Is the DP xmtr mounted directly on the lower flange? If
not how high above and below the lower flange (tap) is it
mounted?

3) Is the DP xmtr high side connected to the lower flange (tap)?

4) Is the low side a dry leg or wet leg?

5) What is the specific gravity of the material in the tank?

6) If the low side is a wet leg, what is the specific
gravity of the fill fluid in the wet leg?

7) What is the elevation distance from the lower flange and
the maximum level?

8) what engineering units are used for level ? mm H2O?

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Instrumentation Interview Questions

What is the use of temprature compensation?

0 Answers

What should be the stanchan Height for installation of Smoke detector & toxic gas detector in field,according to qatar standard

2 Answers

What FLOW METER generally used in Gas plant?

5 Answers Gasco,

how to do loop checking pls email to shanavaska2000@yahoo.com

2 Answers Kentz,

What is the Working principle of Dozing valve?

0 Answers Shree Cement,

What is the input impedence of an OPAMP as an ideal device.

1 Answers CCIE,

Profibus DP is a multi-master system. Would it work on RS-485 4W or not, and justify your answer

1 Answers EIT,

why any measurement made interms of pressure is more accurate ? to be more precise most of the flow velocity is made interms of pressure and it is accurate. what is the reason behind pressure measurement being accurate ?

0 Answers NATPET,

my data card only does run in my mobile so how can change it that it run other mobile & computer and i can stor data in my data card

0 Answers

what is isolation Transformer???...

3 Answers Emerson,

What is intrinsic safety mean.

0 Answers CCIE,

how to check diode wheather it is working or not by using multimeter?

3 Answers

For more Instrumentation Interview Questions Click Here