Answer / arun sangwan

To calculate the lap length-48*D
For calculating hook & bend -As per Is 2502,The anchorage value of the of bend shall be taken as 4*D of the bar for each 45 Degree bend and for the U type hook its always taken as 16* D.
For the bond length(Development Length)-Ld-It is calculated by the formula. and it includes all the values of the anchorages.

Answer / srinu.s

whenever is laps length calclated
dia of the bar* 50 times

Answer / naveen m

hook length is 5*d lap length can been given at the end L/7
and at continuous L/4.

Answer / syed mohd. fareed

Hook - 9d (d- dia of bar)
Bent up - 0.42D (D- centre to centre vertical distance between bent portion and bar )
Lap - 50d (d-dia of bar)

Answer / mohammed aijaz hussain.

Lap length: 45 diameter of the bar (in compression member)
50 diameter of the bar (in tension member)

Bond length: 24 diameter of the bar

Hook length: 12 diameter of the bar

Answer / lalit kumar singh

Lap lenght:- for liquid structure- 50d
for another structure-40d
(like column, beam, slab)
For stirrups Hook:- 2x10d
for corner bend :- (-3d) upto 12dia.
(-4d)above 12dia.

Answer / vinod

Lap length of bar depends on grade of concrete and design
bond. Owing to the Grade of concretes:

Grade of concrete) Tension Compression
M15 56.4d 45.15d
M20 47d 37.6d
M25 40.3d 32.25d
M30 37.06d 30.1d


For stirrups Hook length, it will be (-)2x10d
Bend, it will be (-3d) upto 12dia.
(-4d) above 12dia.

Answer / muthuraj s

it dedpend upon design basics please follwing SP34 & IS2502

Answer / bharat hire

Lap length of bar depends on grade of concrete and design
bond. Owing to the Grade of concretes:

Grade of concrete) Tension Compression
M15 56.4d 45.15d
M20 47d 37.6d
M25 40.3d 32.25d
M30 37.06d 30.1d


For stirrups Hook length, it will be (-)2x10d
Bend, it will be (-3d) upto 12dia.
(-4d) above 12dia.

Answer / phillip gibbs

What is a Link

What is the Systematic Responsibility Site Engineer? Who are the above and under co-oridinating ? What is office & Site co-ordination of Site Engineer?

0 Answers  

plz send me civil q papers of hpcl

5 Answers   Shell,

how to replace 8mm bar with 10mm bar if the the 8mm bar is not available..???

3 Answers   CICEF,

What should be the standard roof height like to be?

0 Answers  

Can we use 16mm dia bar in place of 12mm dia bar in COLUMNS? (if given dia bar is not available on site)

5 Answers   Clover, Rites,

what is the cost of rcc roof casting of 400 sq. ft. in kolkata

0 Answers   L&T, VCCL,

How do we calculate the building footing calculation ?

7 Answers   Dodsal, L&T,

how many shuttering material required for 100 sqm

1 Answers   NRI, Raheja,

how to test the quality of bars???

6 Answers  

How to Calculate the spacing of bars if we use 12 mm dia. bars instead of 10 mm dia. bars. Whereas the 10 mm dia. bars spacing given 0.250 as pr drawing. ?

1 Answers  

if a pipe those configuration (ASTM c 76 class b 450mm dia 2500mm length) fixing for water course those lining of water is 7000 running meter. my question is that if 8 joints of pipe ls leakage and we have not permission to stop the water so which treatment we apply on joint in that in condition.

0 Answers  

What is the Unit weight of coarse sand (F.M- 2.20) ?????

0 Answers   BNF Group, TATA,