DG B-check,C-Check,D-check is depending upon the running
hrs.If the running hrs is not reached as mentioned.How to
conduct the DG checks.
Answers were Sorted based on User's Feedback
Answer / omprakash
B. CHECK 250 HRS OR 6 MONTHS
C. CHECK 1000 HRS OR 1 YEAR
D. CHECK 1500 HRS OR 2YEARS
Is This Answer Correct ? | 90 Yes | 26 No |
Answer / neeraj
DG check can also be done after completion of period like 3
months 6 month and 12 months
Is This Answer Correct ? | 71 Yes | 23 No |
Answer / arunselva
A Check Daily check
B Check 250Hr to 300Hr or 6 Month
C Check 1000Hr or 1Year
D Check 1500Hr or 2Year
Is This Answer Correct ? | 57 Yes | 20 No |
Answer / ganesh singh
A-check Daily
B- check 300 hrs or 6 month All filter & lube oil change
C-check 1500 hrs or 1 yrs (Tapit setting)
D-check 5800 hrs or 2 yrs (HPIT seting)
E-check 10000hrs overhalling (crank
grinding,shaft,actuatoer etc)
Is This Answer Correct ? | 36 Yes | 6 No |
Answer / baskaran.r
the checks are depend on the running hrs. if it is not
reached means engine is not running ok.you can wait till the
running hrs reached. if the stoppage is long you can go
according preservation requirement by the manufacturars
recomendation
Is This Answer Correct ? | 43 Yes | 15 No |
Answer / mayank sharma
DG Checks are depand upon running hours but if running hours is not reached then we should conducts checks as per the time duration as listed below :
A Check - daily
B Check - 300hrs. or 6 months( filter change, lube oil change)
C check - 1500 or 1 year(A+B checks+ injectors & turbo charger cleaning )
D Check - 5000 hrs. or 2 year( A+B+C Checks+ Tappid setting )
Is This Answer Correct ? | 14 Yes | 1 No |
Answer / pavan
If it is not reach the running hours.we can take the number
of days from its working.
Is This Answer Correct ? | 26 Yes | 14 No |
Answer / sk ajibar rahman
"A" - Daily Checks
"B" - 300 Hrs or 6 Months
"C" - 600 Hrs or 12 Months
"D" - 1200 Hrs or 24 Months
Is This Answer Correct ? | 27 Yes | 15 No |
Answer / biswajeet
the checks are depend on the running hrs. if it is not
reached means engine is not running ok.you can wait till the
running hrs reached. if the stoppage is long you can go
according preservation requirement by the manufacturars
recomendation
Is This Answer Correct ? | 12 Yes | 7 No |
how to interlock 3 nos MCCBs using under voltage coil. please provide me circuit diagram?
What is the difference between voltage transformer and potential transformer?
38 Answers ABB, ETA, Maritime Academy, MSEB, Reliance Jio, Voltas, Wipro,
hi frienda We have 250kva cater pillet dg set we are fasing one diffrent proublam in dg we are start dg set after one mint applying load around 450a load but dg was run 3 Or 4 mints after 3 mints dg was shuding down automatic how to face this proublam pls tel any budy
what happens when dc supply is given to the transformer?
what is the working principle of soft-starter & how it diff. from VFD ?????????
WHAT IS FAULT CAPACITY OF HT MOTOR TERMINAL BLOCK? ANY BODY HAVE ANSWER PLZ....POST IT.
plz tell me about detailof induction motor Slip
How to reverse the direction of a DC motor ? By reversing the Armature wires or by reversing the field wires
Sate maximum power transfer theorem?
What is mean by sink and source in term of PLC and drives,where and how they used in logic
what is the use of megger? and types
11 Answers TNEB Tamil Nadu Electricity Board,
How does the slip regulator works as a startor