what we happen if 400 kvar cpacitor banks are on in manual mode and there is n

Categories >> Engineering >> Electrical Engineering
Suggest New Category

what we happen if 400 kvar cpacitor banks are on in manual
mode and there is no load on mains ??????????????

Question Posted / bhupinder singh

7 Answers
10931 Views
HCL, Reliance, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

what we happen if 400 kvar cpacitor banks are on in manual mode and there is no load on mains ????..

Answer / reddy

voltage willl be raise d due to ferranti affect

Is This Answer Correct ?

8 Yes

2 No

what we happen if 400 kvar cpacitor banks are on in manual mode and there is no load on mains ????..

Answer / vinod sharma

If the bamk is on mannual it will lead the voltage.
Due to this the power factor will cross the limit 1 and
with this losses will increase.

Is This Answer Correct ?

6 Yes

2 No

what we happen if 400 kvar cpacitor banks are on in manual mode and there is no load on mains ????..

Answer / rahul shukla

VOLTAGE WILLL RISE AND ALL LOADS i.e motors ect. get
overfluxed as v/f ratio will be high

Is This Answer Correct ?

1 Yes

1 No

what we happen if 400 kvar cpacitor banks are on in manual mode and there is no load on mains ????..

Answer / ashok

power factor is leading and average power factor decreased

Is This Answer Correct ?

0 Yes

0 No

what we happen if 400 kvar cpacitor banks are on in manual mode and there is no load on mains ????..

Answer / er. ankush miglani 9718151073

if all this happen the power factor increases from unity
and the supply is fed back to the system i.e. the load
becomes the source.
or

when capacitors charge to its peak value they will not get
any path to discharge and remains charged i.e. nothing will
happen.

or

practicaly try karne ka yaar.........

Is This Answer Correct ?

2 Yes

3 No

what we happen if 400 kvar cpacitor banks are on in manual mode and there is no load on mains ????..

Answer / chandra

The load power factor becomes leading and load becomes
source and power is supplying to the system instead of
receiving.

Is This Answer Correct ?

1 Yes

3 No

what we happen if 400 kvar cpacitor banks are on in manual mode and there is no load on mains ????..

Answer / anand

user will face the fine from electricity board

Is This Answer Correct ?

0 Yes

2 No

Post New Answer

More Electrical Engineering Interview Questions

BRIEFELY EXPLAIN MEGGAR PRINCIPLE

2 Answers

EXPLAIN THE TERMS "INTEREST AND DEPRECIATION" AS APPLIED TO ECONOMICS OF POWER GENERATION.

0 Answers

is it possible to test of bus bar in high rise building without completed full floor ?

0 Answers

why colour of electrical equipment( like transformer) is grey

10 Answers Trident,

Why do we perform an open-circuit test and short-circuit test on the transformer?

0 Answers

why do we have 230v a.c. as general voltage for domestic supply rather than others?

2 Answers

How to calculate per unit impedance of transformer?

0 Answers

What is the important parts of SF6?

2 Answers

how do you reduce the skin effect

2 Answers

why Y CONNECTION IS BETTER INTERMS OF EFFICIENCY AND P.F FOR A LAOD LESS THAN 40% AND WHY AFTER DELTA IS BETTER FOR > 40%

0 Answers

what is the Excaste meaning of CT Saturation?? 10 P 20, 15 VA, what is the meaning of 10, & 20. if the CT polarrity changed what will happened?? what is the differece between measuring CT & Protection CT?? what is the Saturation Point of measuring CT & Protection CT??

1 Answers

Explain the function of VFD

10 Answers Dalkia,

For more Electrical Engineering Interview Questions Click Here