What are the voltage values for LT,HT,EHT and other
voltages??

Answers were Sorted based on User's Feedback



What are the voltage values for LT,HT,EHT and other voltages??..

Answer / anbuselvan

Low Tension=upto 1KV
High Tension=upto 11KV
Super Tension=22KV-33kv
Extra High Tension=33-66kv
Extra Super Tension=beyond 132kv

Is This Answer Correct ?    165 Yes 39 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / ishan patel

LT voltage is upto 415 volts.
HT voltage is upto 220KV.
EHT voltage is upto 1100KV.

Is This Answer Correct ?    179 Yes 102 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / priyadoss

LT - 230v,440v,upto600v
HT - 1.1kv,3.3kv,6.6kv,11kv,33kv,66kv
EHT - 110kv,233kv,440kv

Is This Answer Correct ?    86 Yes 36 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / shashi nath jha

LOW TENSION (LT)= 1000 (1KV)
HIGH TENSION (HT)=11000 (11KV)
SUPER TENSION (ST)=22000-33000 (22KV-33KV)
EXTRA HIGH TENSION=33000-66000 (33KV-66KV)
EXTRA SUPER TENSION=BEYOND 132000 (<132KV)

Is This Answer Correct ?    45 Yes 8 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / natarajanramkumar

1.L.T (Low tension)=upto 1000 volts
2.H.T (High tension)=upto 11,000 volts
3.S.T (Super tension)=from 22,000 volts to 33,000 volts
4.E.H.T (Extra high tension)=33,000 volts to 66,000 volts

Is This Answer Correct ?    55 Yes 27 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / sukhvinder

LT upto 440V
HT upto 66 kv
EHT above 66 KV upto 1200 KV (under testing)

Is This Answer Correct ?    41 Yes 29 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / ajaykrishna

LT-LOW TENSION---- NOT EXCEEDING 250V
HT-HIGH TENSION---MORE THAN 650 V & UP-TO 33 KV
EHT-EXTRA HIGH TENSION-MORE THAN 33KV

Is This Answer Correct ?    16 Yes 5 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / raja

In India IS specifications are followed which has BS
standard as base.
Normally AC 50 V - 1000V volts are considered LT .
1kV to 66 kV is considered HT and
Above 66 kV is EHT
Voltages below 50 volts is considered Extra low tension

Is This Answer Correct ?    18 Yes 8 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / sr

Low voltage upto 1.1kV
Medium Voltage from 6.6kV to 33kV
High Voltage from 66kV upto 132/110 kV (in Karnataka)
Extra High Voltage from 220 kV & above.

Is This Answer Correct ?    24 Yes 15 No

What are the voltage values for LT,HT,EHT and other voltages??..

Answer / k.gurusamy

LT 230V,433V
H.T 6.6KV,11KV
S.T 33KV
EHT >66KV

Is This Answer Correct ?    11 Yes 3 No

Post New Answer

More Electrical Engineering Interview Questions

my 10 hp submersible pump is tripping when connected through ELCB.I have checked the megger value of the coil's with body.It was found to be 0.2mega ohm.that is leakage is there.But when connected to mccb it is not tripping.no leakage current in the motor.Is it safe to connect to mccb? what are the problem's will arise if future?also tell me in ELCB no neutral is connected to motor.than how ELCB was working?

1 Answers  


which one is the most common system for secondary ditibution

1 Answers  


how to calculate current carring capacity of cable and cable selection? 1) copper flexible cable 2) copper armoured cable 3) Aluminium cable

0 Answers  


what will happen if ac power supply is given to the rotor of an alternator

1 Answers   Goldman Sachs,


synchronous motor of 13.5MW having which type protection? and how to set relay?give me relay setting calculation for different protection for this motor assume efficiency,power factor and other term if neccecery

1 Answers  






what is ten delta test? what is the significanse of it

1 Answers  


what is the use of static frequency converter and static excitation equipment? and where it is employed? for what?

0 Answers   Toshiba,


Is RTCC panel needs any control supply.

0 Answers   HPCL, Schneider,


what is iron loss?

4 Answers   RRB,


how is working the APFC when varying the load?

1 Answers  


what are the advantages by using IGBT in VSC HVDC than thyristor in conventional HVDC

1 Answers   Bhel, Eskom,


what is relay

15 Answers   HPCL, IOCL,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4452)
  • Electrical Engineering Interview Questions Electrical Engineering (16637)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)