Answer / mayank sharma

well this question seems to be incomplete...is rotor is
given the supply alongwith the stator then the machine will
become doubly excited and will atart to behave as
synchronous motor provided the two fields are inter locked.
however if rotor is given supply and the stator is short
ckted then the rotor will move in the direction opposite to
that of rotating magnetic field.

Answer / gaurav dwivedi

rotor would run against the direction of rotating field.

Answer / pratheesh

Didn't mention what kind of motor.
In the case of Squirrel Cage induction motor, it is
impossible to give supply to rotor as there is no winding
on it except shorted copper/aluminium bars.

Answer / arun patil

ROTOR OFF SLIP RING MOTOR START ROTATING OPPOSITE
DIRECTTION OF ROTETING MAGNECTIC FIELD WHILE STATOR WINDING
SHORT CIRCUITED AS ROTATING MAGNECTIC FIED WILLL SET UP ON ROTOR

Answer / p v n vamsi krishna

Once I tried on a 2.7 HP three phase slip ring induction motor. What happened was smoke came from rotor and rotor winding was gone.

Answer / vibhakar

there are two types of IM one is squirrel cage and slip ring induction motors.In squirrel cage rotor windings are short circuited with end rings where we cant give supply therefore this type of motor has more efficiency because losses due to slip rings and brush assembly is less...but in case of slip ring IM in order to increase torque, resistance is added through slip ring assembly

we can give 3 phase supply to rotor and they are callled as rotor fed IM

Answer / ranjit kumar mallick

It is quite difficult to provide three phase supply to a
rotating object like rotor.As you know in case of squirel
cage motor the rotor is shorted through end rings so
breaker will trip once you give supply to shorted motor.In
case you open circuit the rotor winding and then you give
three phase supply but you have check the phase squence of
stator and rotor to make the stator magnetic field follow
the rotor magnetic field.Initially the motor will start
with very high torque but afterwards it will become very
messy to calculate the load current, voltage etc due to the
effects of faraday and lenz law and the behavior becomes
unpredictable. I will sugest not to make such
experiment.Any way the three phase slip ring is mostly
unavailable to make this experiment.

Answer / p

the suipply given to the rotor is difficult.need slipring
to given supply to rotating component.so normally supply
given to stator

Answer / sennapparajan

how ever as per question. if we gine direct supply to rotor
the totor wil be burned due to over current.

Answer / bijay

will act like a transformer ....
if u keep on increasing the rotor current beyond a value it
will burn !!!

What is hipot test procedure?

0 Answers   CCC,

what is meant by Back emf ?where its occur ?

6 Answers  

what is the disadvantage if earth is connected to neutral

6 Answers  

Where the ON LOAD TAP CHANGER is provided in the setp up transformer?

2 Answers  

How to know the back up time for a 5KVA UPS which is connected to 15 nos. of computers? Is there any formula for this? pls. tell me.

1 Answers   S V Sugar,

why the capacitors works on ac only

5 Answers  

We have a distribution transformer of 750KVA/11kv/440v and an AVR (Servo Stabilizer) of 750KVA on the LT side of distribution transformer. Also we have an ACB of 1200A on the output of distribution transformer (that is on the input of AVR). We want to have an MCCB on the output of AVR. What should be the rating?

0 Answers   SSPL,

Which types of following motors are most efficient?

0 Answers  

What is the PIU.

1 Answers   Jindal,

what's the difference between induction generator and synchronous generator?

1 Answers   IBM,

why the power cut problems occur in tamil nadu? may i know the exact reason.plz

17 Answers  

what is the power factor of choke coil used in tubelight

12 Answers   Bajaj,