what is the power factor of choke coil used in tubelight

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / mayurbtechanand

12 Answers
27594 Views
Bajaj, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

what is the power factor of choke coil used in tubelight..

Answer / lokeshraj

The power factor of a choke coil is near to zero. as PF=cos
(angle). In choke coil the angle is near to 90.

Is This Answer Correct ?

35 Yes

14 No

what is the power factor of choke coil used in tubelight..

Answer / rohan

choke is a inductive load and inductive load is always have
lagging pf

Is This Answer Correct ?

7 Yes

0 No

what is the power factor of choke coil used in tubelight..

Answer / narendra

It should be zero

Is This Answer Correct ?

8 Yes

6 No

what is the power factor of choke coil used in tubelight..

Answer / lucky

Pf means power dissipated in the circuit. So in case of pure inductor power consumption is zero so power factor is 0.

Is This Answer Correct ?

4 Yes

2 No

what is the power factor of choke coil used in tubelight..

Answer / narendra saini

it should be 0.8 to unity because choke improve pf...

Is This Answer Correct ?

10 Yes

9 No

what is the power factor of choke coil used in tubelight..

Answer / simon

The watt of the choke is 40 so at 250v it will be 0.16.

Is This Answer Correct ?

0 Yes

0 No

what is the power factor of choke coil used in tubelight..

Answer / dev

i think it should be 0.7 to 0.8 because we use
it step up the voltage like transformeri

Is This Answer Correct ?

11 Yes

12 No

what is the power factor of choke coil used in tubelight..

Answer / yadav

its 0.8 because tubelight improve the power factor

Is This Answer Correct ?

2 Yes

5 No

what is the power factor of choke coil used in tubelight..

Answer / dj

it is .6 acc to my book

Is This Answer Correct ?

0 Yes

5 No

what is the power factor of choke coil used in tubelight..

Answer / parvesh lathar

0.5 lag

Is This Answer Correct ?

1 Yes

8 No

Post New Answer

More Electrical Engineering Interview Questions

DIFFERENCE BETWEEN GROUND AND NEUTRAL?

4 Answers

why v/f ratio to maintain constant in speed control of induction motor?

3 Answers

HI....HOW CAN BE MESARED THE VALVE OF NEUTRAL GROUND RESISTOR WHIC IS LOCATED AT SWICHGEAR ON GENERATOR SIDE....

0 Answers Jindal,

how to determine Sq.mm size of finolex power cables.

0 Answers Finolex,

Baud rate is used to descrice...?

2 Answers

what do you mean by 1 ton in AC`s

36 Answers Bhel, Bosch, ITC Infotech,

will there be any problem by recovering slip from single phase induction motors?

0 Answers

if my load is not in continuous operation so what type of panel is required APFC or fixed capacitor bank without APFC whether C.T is required in both cases compulsory? explain detail

1 Answers

what is the effect of connecting three phase supply lines to three phase auto transformer output terminals through a fuse of 10Amp and a circuit breaker (MCB). Is this connection permanently destroy the transformer?

0 Answers

Can we use 11kv Trivector Metre or Energy metre instead 33kv Metre at 33kv Over Head Line metering purpose?

5 Answers Bhel,

IN A HT CABLES i.e. 1.9/3/3 kv, what is the meaning of 1.9 and 3.3.

1 Answers

why do we prefer a 3-phase delta connected load rather than star connected?

4 Answers

For more Electrical Engineering Interview Questions Click Here