Answer / ujjawal u. d.

the penetration caused by standard Condition i.e.
Standard Weight= 100 gm
Standard temp. = 25 Degree C.
Standard penetration time = 5 Seconds
Unis = 10th of mm to show the results and avoiding Errors
e.g. if the value is 30/40, the 30/40 is the bitumen
penetration value (tested in standard condition) lies
between 3 to 4 mm.

Answer / nilesh ghadge

IT MEANS IT HAVING THE PENETRATION VALUE BETWEEN 30 TO 40

Answer / tawalbeh

yes, and the unit is (0.1mm) ..
e.g: 80 = 8mm = 0.8cm

Answer / venky

the needle denotes in 1/10th 's ofmm....so it mean 3mm to 4 mm

Answer / anwar_eng04

the rage 30-40 means the bitumen has having grades between
these two valus and and it is determined by average
peneteration value of the test which conducted by the
instrument called penetrometer.

Answer / hossain

Penetration value (tested in standard condition) lies
between 3 to 4 mm.

Answer / abir kumar ghosh

30-40 means bitumen having penetration of a needle between
30-40 mm with standar weight on it at 25 deg Centigrade.
Lower the penetration is higher the viscosity.
The test is done with the apratus called Vicats apparatus.

Answer / abir kumar ghosh

30-40 means bitumen having penetration of needle (with
standard weight)between 30-40 mm in 5 seconds at 25 deg
cent.
The test done with a apratus called Vicats apparatus.

Answer / aditya richie

30-40 means bitumen having penetration between 30-40 mm .
The test done is called bituminous penetration test ,
machine used is vicats apparatus.

Answer / bhuwan

penetraion is 30 t0 40 mm by 25 deg tem

percentage of steel in one cubic meter of concrete

1 Answers   Jacobs Zate,

why we use for testing of compression strength concrete the size of specimen 150x150x150. why we are not using another dimension like 100x150x100 uneven dimension.

0 Answers   Guru Nanak,

What is the average density of soil?

0 Answers  

how many types of foundation

6 Answers   Synergy,

How Much Anailed Wire (Binding Wire) use Per KG in Running Meter ?

1 Answers  

what is coping?

11 Answers   GKC Projects Limited GKCPL, Technical Construction, Vijai Electricals,

Which Cement is good for concrete, Is that grade 33, 43 or 53?

10 Answers   Modi Builders,

Cement proportion in Fly ash bricks and type of cement to be used ?

2 Answers  

how to calculate 1 cubic meter rcc concrete 1:1.5:3 ratio ,how much aggrates and sand , quanitites

3 Answers  

1.DIFFERENCE BETWEEN NOMINAL MIX AND DESIGN MIX? 2.WHAT IS MEANT BY STRUCTURAL DESIGN? 3.IN STAAD WHY WE RELEASE MOMENT TO A MEMBER? 4.ON WHAT BASIS PARTIAL FACTOR OF SAFETY ARE DECIDE?FROM THE LOAD COMBINATION? 5.WHY WE PROVIDE EXTRA BAR & DEVELOPEMENT LENGTH AT TOP? 6.FULL FORM OF SPT & SMB? 7.WHAT IS MEANT BY ITP IN A CONSTRUCTION PROJECT? 8.WHAT IS LEAST COUNT OF THEODOLITE SURVEY? 9.WHAT ARE THE CAUSES OF FAILURE OF FOUNDATIONS AND REMEDIAL MEASURES? 10.WHAT ARE THE VALUES OF COMPRESSIVE STRENGTH? 11.STEEL CALCULATION FOR FOOTING,BEAM & SLAB? 12.WHAT IS MEANT BY GANTRY GIRDER? 13.IN SITE HOW WE CAN IDENTIFY THE ONE WAY, TWO WAY SLAB? 14.DIFFERENCE BETWEEN ANCHORAGE LENGTH & DEVELOPEMENT LENGTH? 15.BEARING CAPACITY OF STEEL SHUTTERING?LOAD CARRYING FOR SHUTTERING?

3 Answers  

what is the sequence of the activities in the typical under ground water tank including civil & MEP works.

0 Answers  

Is there any codal provision for the use of Micro Silica in concrete?

0 Answers   GIL, SPCL,