Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


Convert a pressure, level, flow, or temperature process
variable value into the appropriate pneumatic or electrical
value given different types of instruments.

Answers were Sorted based on User's Feedback



Convert a pressure, level, flow, or temperature process variable value into the appropriate pneuma..

Answer / suraj rajagopalan

The instrument which converts a physical qty(such as
pressure,level,flow etc) to an electrical qty is
a "Transducer".

Is This Answer Correct ?    50 Yes 5 No

Convert a pressure, level, flow, or temperature process variable value into the appropriate pneuma..

Answer / sattar

pressure=(use bellows to get pneumatic output or use pirani
gauge for electrical output).

level=(use float type sensor )

flow= (use electromagnetic flow meter)

temperature=(use RTD or thermocouple)

Is This Answer Correct ?    23 Yes 0 No

Convert a pressure, level, flow, or temperature process variable value into the appropriate pneuma..

Answer / sushruta

transmitter

Is This Answer Correct ?    8 Yes 4 No

Convert a pressure, level, flow, or temperature process variable value into the appropriate pneuma..

Answer / jadhavamit

You can use pressure switch for pressure indication,
for level u can use DPT
for flow u can use mass flow meter/turbine flow meter/magnetic flow meter/ultrasonic flow meter
and for temperature u can use RTD/Thermocouple.
keep in mind 1 note that every transmitter output is 4-20mAh these is read by every controller and switch output is in form of 1 or 0, means 1 high to its set point and 0 below setpoint.

Is This Answer Correct ?    2 Yes 1 No

Convert a pressure, level, flow, or temperature process variable value into the appropriate pneuma..

Answer / kishore kumar

Converter changes the format of the signal without changing the energy form that is voltage to current signal conversion.
Transducer changes the one form of energy to other, e.g.thermocouple changes temperature into voltage, RTD changes temperature into resistance.
In this contest transducer is right answer.

Is This Answer Correct ?    0 Yes 0 No

Convert a pressure, level, flow, or temperature process variable value into the appropriate pneuma..

Answer / sn

it is a differential pressure transmitter

Is This Answer Correct ?    4 Yes 14 No

Post New Answer

More Instrumentation Interview Questions

why use to 250 ohm for hart protocol and why hart communicator not communicate without 250 ohm 

4 Answers   OMV,


What is a PID?

6 Answers  


if I did short to both AO connections, channel will burn or what? m sure in AI it will damage to channel. But what will happens in AO?

1 Answers  


units of pressure,flow, level,temperature? principle of pressure gauge? calibration of pressure tx., level tx., temperature tx.flow tx.? description of two wire ,three wire and four wire R.T.D.? WHAT IS INPUT AND OUTPUT OF TX.? WHAT IS INPUT AND OUTPUT OF R.T.D. AND THERMOCOUPLE? WHAT IS HOT LOOP AND COLD LOOP? WHAT IS INPUT AND OUT PUT AND OUTPUT OF D.C.S. AND P.L.C.? PRINCIPLE AND WORKING OF HART? WHAT IS PNP AND NPN PROXY? CALIBRATION OF PRESSURE ,LEVEL ,FLOW SWITCH? DESCRIPTION OF FIELDBUS FOUNDATION? WORKING OF SOV.?

2 Answers  


what are the different types of Protocols? & their applications.

6 Answers   Infosys, Sitara Chemical Industries, Syntel, VSNL,


what is the working principle of ABB gas analyser of kiln in cement industries

4 Answers  


what are the following documents comes under loopchecking

1 Answers   Heisco,


In vortex flow meter how can measure the frequency of vortex generated by vortex flow meter

4 Answers   Cadila,


FOR CO/CO2/O2/NOX applications which of the following manufature is best? and what is the basic principle of gas analysers? ABB/YOKOGAWA/EMERSON/SIEMENS/TELEDYNE/THERMOFISHER

4 Answers  


Can a Differential Pressure Transmitter be used as a normal pressure transmitter??

3 Answers  


How to get Cv of control valve having following parameter ,i.e inlet pressure 4.5kg/cm2 outlet pressure 1 kg/cm2 specific gravity 0.808

3 Answers  


which type of zones used for boiler? & why ?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)