Answer / jigaranadkat

Dear Prasanth,

Please rest assured that your control network is good you
only have the problem in your open network. Thats the
reason that your plant functionality will not be affcted
but you can not download in to HIS0163.

Please follow the below procedure and let me know the
feedback...

1) Check the IP address of HIS0163. It should be :
172.17.01.63 and subnet mask : 255.255.0.0
2) Check for corruption of ethernet driver : (Right click
on my computer---> Go to device manager---> Check for
ethernet driver corruption).
3) Go to run.... Type CMD and give folling command...
ping 172.17.01.63... You should not face any dropped
package.
4) Go to run and type: \\172.17.01.63 or \\his0163
You should be exposed to common shared folder CS1000
5) Disable firewall in HIS0163.

7001/7002 is the code that your ENG STATION is not able to
find HIS0163 in the network.

* As a default setting, due to some group policy setting ..
Connection with blank password will be denied access. So
try to have a common administrative password for HIS0164
and HIS0163 and for operator USER NAME=CENTUM and PASSWORD=
CENTUM.

You may write your feedback to

anadkat.jigar@gmail.com

Hope this will resolve your problem.

Thanks & Regards,

Jigar Anadkat
Instrument Engineer
IBN RUSHD a SABIC affiliate.

Answer / prashanth

thanks mr Jigar Anadkat
Instrument Engineer
IBN RUSHD a SABIC affiliate.

your suggession really helped

actualy firewall was turned on in HIS0163.
I TURNED OFF the fire wall and gave download,then it got
dowloaded successfully.

thank you

Answer / karthik

This means that HIS0163 is down and not connected to the
control network. Check Vnet/IP BUS1 and BUS2 connections and
the IP setting.

Once it's rectified , you should find HIS0163 in .SO (System
status overview).

Answer / jaguirre

Dear Prashath,
Just found your solution here in this website.
Can I asked for other possible solutions. All 5 items you gave was checked and verified but still, i'm not able to equalize.

Thanks and hoping for any suggestions.

Regards,
John

Answer / jaguirre

Dear Jigar Anadkat / Prashath,

This is the error.

Equalize start. HIS1145
WARNING: Could not connect to equalize destination. (7001) Retrying. Number of retries = 0/1
ERROR: LdXopsLoadMain: connect error 10061
ERROR: Processing terminated due to connection error. (7002)
Equalization end with errors. HIS1145
---- ERROR = 2 WARNING = 1 ----

Regards,
John

Answer / sha

replace your vnet card

Hi, I'd like to know the purpose of MOS (maintenance override switch). At site, these switches are installed in a stanchion with the transmitter (connected to ESD). thank you.

3 Answers   Adani, Adani Wilmar,

what do you know about Foundation Fieldbus?

1 Answers   CCIE,

Which wiring connection is preferred in motor for industrial use?

2 Answers  

generally transmitter power supply having some range(12v to 35v) but the out put(4-20 mA) must same for given input.If we vary the power supply voltage then output mA also to be change according to V=IR. Is there any voltage regulator in the transmitter ?

1 Answers   Indian Steel,

why fuse block is not used for AI signal?

0 Answers  

If we increase PI controller what will be action.

1 Answers   IMECO,

WHAT IS DIFFERANCE BETWEEN INSTRUMENT AND EQUIPMENT

1 Answers   Lupin,

Im having problems with interfase betwen SPI v7.0 and SPPID v5.05. Previous versions of Intools shoul be fixed with SPPIDproj.ocx file. It was necessary to replace this file with one that allows the connection between different versions of SPPID. It is necessary in the current version to do the same?Thanks

0 Answers  

tion 0,50,100% equql to voltage formula?

1 Answers  

We have a Yokogawa Micro-XL DCS, which is having around 300 I/O, but whenever there is any wire gets grounded in field, the 24v supply to all loops gets dipped & all the indications at DCS goes to IOP(shows input open), at present we have fixed 500mA fuses in all the lines but which does not working. Does it required to replace with lower amps fuse, then how much or is there any other solution for this.

2 Answers  

I have seen the Temperature element (T/C & RTD) installed in process line on 45 degree position, Why? What it mean? How many types of tapping position for temperature elements?

4 Answers  

How the sizing of the analog signal cable is calculate?

0 Answers   Reliance,