Answer / subodh

1 Kg/cm2(g) = ? mmWC(g).

is mmWC is always absolute?

Answer / shubham chouhan

10000 mmwc = 1 kg/cm2

Answer / anmol chute

MMWC and Kg/cm2 both are pressure measuring units but difference between both unit is in pressure range ,means MMWC unit used to measurement of low pressure and Kg/cm2 used for High pressure measurement.Because,
1Kg/cm2=10000 MMWC

Answer / vikesh mourya

Unit Conversion :-

1 kg/cm2 = 0.98 bar

1 kg/cm2 = 98.06 kPa = 0.098 MPa

1 kg/cm2 = 980.665 mbar = 10000 mmwc = 735.56 mmhg = 29 inhg

1 kg/cm2 = 14.22 psi (lb/in2)

1 bar = 1.01 kg/cm2

1 bar = 100 kPa = 0.1 MPa

1 bar = 1000mbar = 14.50 psi

BY:-
Vikesh mourya

Answer / tara chandra sah

To measure low pressure we need to use this unit of
pressure Hence 10000mmwc=1kg/cm2


1 Kg/cm2 is 1.033 bar or 1.033x10^5 N/m2
10000 mmwc= 1 kg/cm2
low pressure can also be
used for but the error in values will be more.
Basically 10000 mmwc is 1 kg/cm2 a.

Answer / bipin

When use minimum pressure than mmwc & Higher press kg/cm2g

Answer / manimaran

when we r measuring very low pressure :: mmWC and general terms is Draft pressure and measuring high pr. :: kg/cm2/bar/psi...for example we r measuring like boiler furnaces pressure and flue gas path (draft) i.e very low pr.(250mmWC) so we r measuring in mmWC, and when we are calibrating the flow, draft and level transmitters we will indicate the range in mmWC. The error value for FSD will be higher side for the transmitters which are calibrated in mmWC.

Answer / sk singh

We are using the mmWC for very low or lower than 0 and more than 0 we are using Kg/cm2.

Answer / vaibhav v t

First of all using kg/cm2 for pressure is absoltely
wrong.pressure is force per unit area and unit of force is
newton, so pressure unit is N/cm2 and not kg/cm2.MMwc is
used for low pressure measurement and N/cm2 is used for
high pressure measurement.

What is the use of single seated valve?

0 Answers  

Full form of KKS when use DCS.

0 Answers  

What is pre-commissioning and commissioning ?

1 Answers   Armco,

can anybody tel me how a vfd or any field instrument communicates/interface with plc/scada/cs.

0 Answers   Honeywell,

A length of steel pipe is used to carry sea water to a desalination plant. An adequate corrosion allowance must be specified and indicated in the piping specification, which affects the _________________________ of the pipe

0 Answers  

what is differnace between radar level tranmitter & hart type tranmitter?

3 Answers  

How to check loadcell working or notworking

2 Answers  

what is RTV function in in process control?

0 Answers   Colgate,

In closed loop control there are several “blocks” used to show the interactions between the process and the control system. These blocks are referred to as the “process” and the “controller.” Describe the relationship between these two blocks when creating a well tuned control loop.

1 Answers  

Can a Differential Pressure Transmitter be used as a normal pressure transmitter??

3 Answers  

Tell me the field calibration procedure step by step with diagram of temperature transmitter, temperature indicator, flow indicator, level indicator, control valve, thermocouple, pressure indicator (digital & analogue).

1 Answers  

what is principal of pressure transmitter?

5 Answers   Hindalco, SPB,