Interested to Buy Any Domain ? << Click Here >> for more details...
what is the diffrence between mmwc and kg/cm2 for pressure
measurment when we are using mmwc and when kg/cm2 and why?????
?? what is the reason
- 19 Answers
- 204445 Views
- Ecoboard, Jindal, Sepco, I also Faced
- E-Mail Answers
Answer Posted / vikesh mourya
Unit Conversion :-
1 kg/cm2 = 0.98 bar
1 kg/cm2 = 98.06 kPa = 0.098 MPa
1 kg/cm2 = 980.665 mbar = 10000 mmwc = 735.56 mmhg = 29 inhg
1 kg/cm2 = 14.22 psi (lb/in2)
1 bar = 1.01 kg/cm2
1 bar = 100 kPa = 0.1 MPa
1 bar = 1000mbar = 14.50 psi
BY:-
Vikesh mourya
| Is This Answer Correct ? | 2 Yes | 0 No |
Post New Answer View All Answers
Where is wet leg is used?
what about your moleg in pogrees with company
Explain PID, ON/OFF, Controls
how to measure oxygen which methods are using?
Q1: Consider part of a control loop, which excludes the transmitter, consisting of a process, a controller and a control valve which may be represented by two dead times of 0.5 min each and three exponential lags of 0.8 min., 1.0 min. and 1.5 min. respectively. We wish to express this system as an overall first order plus dead time (FOPLD) model ie gain, time constant and process dead time. (We will see later that this is often done, to simplify controller tuning). For this exercise, gain is considered to be 1.0. (A) If the transmitter is a flow transmitter whose behaviour can be described by a dead time of 0.2 min. and an exponential lag of 0.5 min. in terms of the overall dead time and overall first order lag how can the system behaviour be approximated ? Overall dead time = Overall time constant = (B) If the transmitter is a temperature transmitter with a temperature sensor in a protecting well whose behaviour can be described by a dead time of 0.7 min. and an exponential lag of 15 min. how can the overall system behaviour be approximated now? Overall dead time = Overall time constant =
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
it is possible to check the fail safe condition in pressure transmitter. if possible how?
Can any body help to get Rsemulator 5000 free from internet if possible then give me any link or any help .
What is Positive Calibration and Negative Calibration?
what is 24vdc live and dry supply
can any one tell me when ongc placement test and its forms is available????/ pls tell me if u know
how to measure draft pressure in transmitter pl. give its single line digram
Programmable Logic control.
typical loop drawing of a simple feedback control comprising of one transmitter and one control
we are using centum vp as monitoring with Dell precision work station T3600 but some times PC(s) are restarted automatically . how we can solve this problem? thanks
