Interested to Buy Any Domain ? << Click Here >> for more details...
how the lap length is calculated in reinforcement of 110mm
dia steel of Length 15.00 mtrs. & grade of concrete is M20
- 22 Answers
- 105395 Views
- L&T, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / raghuram
I THINK IT IS NOT 110MM IT IS 10MM . FOR SIZE OF ROD THE
LAP LENGTH IS 50 TIMES THE DIAMETER THEREFORE
50X10=500MM.FROM IS 456 200.
| Is This Answer Correct ? | 310 Yes | 35 No |
Answer / rammy
Lap Length is equal to
50D for Tension zone : 50*10 =500 mm
45D for compression zone : 45*10 =450 mm
| Is This Answer Correct ? | 84 Yes | 23 No |
Answer / ramesh konduru
For any dia the lap length should be calculated as per IS:
456 is 50 times the dia of he bar.
| Is This Answer Correct ? | 67 Yes | 18 No |
Answer / sadashiv
the rods more than 32mm dia not used for lapping accoding to
is 456 2000 go to the weld only
| Is This Answer Correct ? | 56 Yes | 16 No |
Answer / mithosh g nair
if dia is 110 mm then that bar must be welded. bars below 32mm dia
the lap length
In tension 50* dia
In compression 45 * dia
| Is This Answer Correct ? | 34 Yes | 4 No |
Answer / bharathiraja
I think this question is entirely wrong. Where u using the110 mm rod!!!!???
| Is This Answer Correct ? | 22 Yes | 2 No |
Answer / rajesh
how to calculate the exact weight of one ring if example
1'0"X 0'9" ring size
| Is This Answer Correct ? | 27 Yes | 10 No |
Answer / jayshankar dwivedi
Lap Legnth is eqal to = (yield stregneth * Dia of stell)/
4* Bond stregnth of Concrete
| Is This Answer Correct ? | 36 Yes | 22 No |
Answer / akshaya kumara nandi
I think it is fifty times of diameter of TMT bar
so it is 50 x 10mm =500mm.
| Is This Answer Correct ? | 11 Yes | 0 No |
How much kg of sand,cement will be for 1 sqmt(Blockwork-size 400x200x200)1:4 ratio & same for plaster
Different sizes of Hollow blocks and its weight. Thanks.
I want to know the relevant IS codes of practice which deals with different testings of cement-sand mortar (nominal mix)that is being normally used for brick work or plaster work in the construction work.
rate analysis for cement pointing 1:4 , for 100 sq m
what is Brick crushing strength(PSI)?
what is the sp.gravity of sand?
what could be the production cost of 1 cum of concrete by CP30 plant
how to determine pile length and diameter of pile is there any thumb rule?
What is the ratio of cement, sand, aggregate of mix M25
20 Answers CCCL, Sarvottam Cement,
in m25 concrete what is m.
What is the outturn of Ceiling plastering
What is Bearing Capacity of Soil? How will you calculate for a particular type of Soil?
5 Answers Nagarjuna Construction,
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
