Answer / vinesh prajapati(9974250705)

Transmitter means Trasmit single from one place to another
place,throught cable,by air And
converters means convert signal one form to another form

Answer / earnest

A transmitter senses the measured variable , convert same
into an analog signal of 4-20 mA and finally transmit same
to the remote control, while a converter is a transducer
which converts one form of signal to another. e.g. an I/P
which convert current into pneumatic.

Answer / peer mohamed

Transmitter is used for boosting the low signal and send it through communicate for a long distance. It's mainly in half duplex mode only. But Converter converts one medium of transmission signal to another medium in half or full duplex mode. For example, full duplex single mode fiber to UTP converter used in CCTV applications.

Answer / muneebu rahiman. p.v

A Transmitter boost the very low level output of a
Transducer and transmit (wired or wireless) the same to
drive the control element.But the Converter change one form
of energy to another form

Answer / gautam

Tx. Means transmit the single as 4 to 20 ma which should be in electrical form only but in case of converter is nothing but transducer which converts 1form of energy to an another form whether it can be mechanical to electrical or electrical to mechanical or electrical to electrical.....

Answer / ankit sharma

transmitter used to convert physical signal into 4-20 mA or
0-10 V but convert convert pulse in form of digital signl

Answer / grajesh

Tranmitter will convert the phisical parameter to electical
parameter,Eg: Pressure to Current , while converter will
convert the signal for same Eg: Current to Voltage , power
to Current

Answer / ulaganathan

AN CONVERTER IS ALSO CALLED AS RECTIFIER . SINCE
IT IS USED TO CONVERT A.C TO D.C. WHEREAS AN
TRANSMITTER IS AN ONE USED TO TRANSMIT THE SUPPLY
FROM 1CIRCUIT TO OTHER CIRCUIT

Answer / dhayalan raja

what is the Instrument Hazardouce Area ?

tell about various protocols used in different plcs

3 Answers   Emerson, Samtel,

what are the different types of Protocols? & their applications.

6 Answers   Infosys, Sitara Chemical Industries, Syntel, VSNL,

How u will setup SPI(2007) on Citrix Server (Thin Client Mode)? Plz Justify?

0 Answers  

1. what is 3 point calibration & 5 point calibration? 2. If we use hart communicator to set the LRV & URV of a smart transmitter, did we calibrate the transmitter? why? 3. Make a complet list if meterials needed to properly connect a pressure gauge to a steam pipe using 1/2 inch stainless steel tubing. The gauge connections is 1/2 inch NPT-M and the steam pipe tap has a 1/2 inch female coupling, compression fittings are use. 4. What are the tools in loop checking? 5. What would the ISA symbol of a square root extractor look like? 6. What would you do to completely prepare for the configuration? 7. What safety measures must you undertake when doing configuration? 8. what are the two most commonly use programming languages used when we configure a PLC? 9. What would you do if you accidentally skipped a step in the configuration procedure? 10. How would you know if the configuration were sucessful? 11. Name at least 3 selections available when we configure the burnout protection of a controller?

3 Answers   EI Electrotechnical Institute,

how to make a calibration for differential pressure

2 Answers  

how ranges is decided for drum level or dearator level,in my pplant i have seen for boiler drum range is -1000 to 1000mmwc, while for dearator -2000 to 0 mmwc ,why they decided to take this range ?

2 Answers  

how to define range of dp level xmeter in open tank

1 Answers  

Describe the concept of Gain Scheduling, as currently found as an option in some controllers.

1 Answers  

WHAT IS THE Differance b/w on/off & pid control valve?

10 Answers  

what is span value and zero ? and how set ?

0 Answers  

why magnetic flow meter is not used in thermel power plant operation

2 Answers   JK Paper,

How we can do the linearity test for Bently Naveda Vibration Probe?

1 Answers   Sabic,