Answer / siddharth agasti

class ps ct is a protection class ct.it is used for
differtial proction,distance proction.

Answer / chetan joshi

Protection class CT are 5 p10 and 5 p 20 and PS class ct
are used where neutral point is available such that star
conneccted secondary of Transformer and alternator ,it is
used for differential protection.

Answer / shivaji mangalagiri

all the protection cts like over current
relay and earth fault relay of transformer,Alternator and
HT motors are having core 1 and core 2 options. CLASS PS
type is used only for differential protection purpose of
transformer,Alternator and
HT motors only. and this type of cts are available only in
PAIR SCHEME (PS) AND their turns ratios,
impedances, VA burdens, knee point etc all these critical
parameters are exactly matched with each other.

Answer / s.rajasekar

the saturation point between the ps is higher than
protection class & metering.and the accurracy is also
higher then protection CT. It has highly efficient so it is
mosly used in sofasticated protections ( REF,DIFF,DISTANCE )

Answer / patel indukumar

Protection class is ued in protection like over current
relay and earth fault relay of transformer,Alternator and
HT motor.PS class is used in DIfferential protection like
transformer,Alternator and HT motor.

Answer / manoj

Both Protection class and class PS CTs are used in
protection circuits only. As someone mentioned earlier,
class PS CTs are special CTs used in all types of
Differential Protetion scemes. they generally come in pairs
and they are special in sense their turns ratios,
impedances, VA burdens, knee point etc all these critical
parameters are exactly matched with each other.

Answer / satheesh

the saturation point between the ps is higher than
protection class & metering.and the accurracy is also
higher then protection CT. It has highly efficient so it is
mosly used in sofasticated protections (DIFF,DISTANCE )

Answer / mauhammad yasir abdul-rub

The Difference Between protection class and metering class
is mainly of saturation, the saturation values of protection
class is higher as when fault occur protection CT must not
get saturated as high current flows and metering CT can be
saturated as when fault occur metering is not necessary,
accuracy is also a factor but not the main factor

Answer / selvam.s

Protection CT:

this type of CT can be used for protect the breakers.

5P10,5P15 & 5P20 are called protection current transformer

1) 5 means accuracy of sensing fault current
2) 'P ' means "protection"
3) 10,15 & 20 means ( no.of times ( 10,15 &20 ) X actual
current rating of breakers .

PS CT:

PS means protection special current transformer.

this type CT can be used for differential protection in
transformer & in alternator.

Answer / r.suryamuthuraman

if any fault occurs core needs to saturated for protection
of ct.because ct secondary ckt will goes to relay current
coil .secondary ckt of ct will having resistance and
current.to avoid saturation want to decrease the burden of
ct.ps means special protection having high accuracy than
other class

how to use single phase supply for a three phase equipement.

12 Answers  

in ac system the current wave form becomes zero for every half cycle then how can we get continuous supply can any one answer to this plsss

2 Answers  

what type of motor is used in fan

6 Answers  

i will applied in 1U-1W on 440 volt primary delta side. what is the result of magtic balance test

0 Answers  

what is the difference between 11kv and 13.8 kv? why we can't used one of these 2 sources?

2 Answers  

slipring induction motor starting time Lrs operating why lrs starting time lrs outer body didn't get shock

0 Answers   Ramco,

how to calculate the watts from the tr

1 Answers  

how can i find ct ratio of meter by seeing name plate of meter and how it should be used in MF calculation if it shows only-/1???

0 Answers   Harshal Electrical,

what is sevice settings for mccb?How can be it setted?

1 Answers  

While elctrical load on DG,capacitor banks kept off why so? If capacitor banks on is their any effect DG?

4 Answers   IL&FS Infrastructure Leasing Financial Services,

What are operating procudures & Safety precautions to be observed while operating OLTC in manual mode ?

0 Answers   NTPC,

in HT service 3ph 4 wire service Y-phase voltage shows zero . whether it is meter fault? or what be the reason ? if y-ph voltage zero ,can current is recorded? reasons for failure?

0 Answers   apspdcl,