Answer / forhad

1.Electrical using AC current, Electronic using DC current
2.Electrical means 'Flow of Electron', Electronic means
'Study of Electron'
3.Electrical deals with 'Analog Signals' and obey the Ohm's
Law.On the other hand Electronic components are made to deal
with 'Digital Signals (0, 1)', and they are Semiconductor
devices which never obey the Ohm's Law & implemented with
logic gates.

Answer / birendra singh

We can not distinguish in terms of power bcoz, in
electronics we also use high power.
Ex: in Television picture tube we use 200 times of applied
voltages. it is approx 4000 volts to 5000 volts.

So in electronics we use only and only semiconductors
devices.

but in Electricals we use only Electrical devices.

Answer / manickavelu palanisamy

ELECTRICAL/ELECTRONICS
1."electrical" instruments deal with 'Analog' signals/Electronic' instruments are made to deal with 'Digital' signals.

2.Conductors, certainly obey Ohm's Law/semiconductors devices which never obey Ohm's Law and implemented with logic gates.

3.electricity controls something physical (a motor, illumination, arc welding), which is consider electrical/electronic if the electrical use is dealing with information like a radio signal or digital computing.

Answer / najeem.a

Electrical is the study of charges in a conductor and deals
with high amount of current with low frequency.
Electronics is the study of charges in Vacuum,liquid and gas
also it deals with low amount of current with high frequency.

Answer / ashok kumar gc

Electrical deals with genration, transmission & utilization
of electric power
where as electronics is deal with microcurrents to transfer
the data or switch on the devices..etc

Answer / najeh msallam

electronic it is apart of electrecity which uses
simiconductors and logic gate same and , or ...etc and
electronic uses low current d.c

Answer / nobel

electronics is the study of behaviour of semiconductors.
Electrical is the study of behaviour of Conductors and
Insulators.

Answer / anil chauhan

Simple In Electrical Current Flows on amp and high higher
then 25 volt , But in electronics Current flow on mili amp
and voltage lower then 25 Volt,

Answer / prasad

electrical is for high voltage
electronics is for low voltages

Answer / abhiraam

electrical makes use of analog signals....electronics makes
use of digital signals....

why we use negative feedback in control system.

2 Answers  

Hi frnds :) plz tell me that i have 100 KVA 3 phase generator so by thumb rule 100*1.4 = 144 amps and generaly we can operate at 80% load...so it will 144*0.8 =112 amps.... so now i m confused about single phase load.....if we use that generator only for single phase the that 112 amps is total single phase load or i can give 112 amps at red 112 amps at yellow and 112 amps at blue.... i mean that total single phase load that 100 KVA generator will take is 112+112+112=336 amp ??

2 Answers   FWO,

is there any phase difference occurs while primary and secondary side mutual induction occurs?

0 Answers  

For two systems transmitting the same amount of real power, the system with the lower power factor will have higher circulating currents due to energy that returns to the source from energy storage in the load.???

0 Answers   Bhel,

PLS MENTION QUESTIONS ASKED IN IOCL INTERVIEW FOR ELECTRICAL EGG??

0 Answers  

What is maximum demand?How can we caluclate it?

3 Answers   TATA,

L.A. (Lightening Arrester) is located at a place from where transmission line enters the transmitting substation. So L.A. (Lightening Arrester) is the first equipments which has to encounter with lightening, high voltage surges and switching surges. It has to absorb energy of lightening, high voltage surges, and switching surges. L.A. (Lightening Arrester) is made up of layers of semiconductors. If these layers can not tolerate energy released by lightening, high voltage surges, and switching surges the L.A. (Lightening Arrester) blasts.

0 Answers  

1.ZEBRA conductor(large size) 2.KUNDHA conductor( small size ) 3.panther conductor(very small ) 4.lepard conductor (very very small)

0 Answers  

what is the per unit cost of generation of electricity at thermal,hydro,desael,solar,gas power plant

1 Answers  

What is VCB? where it is installed at SP. What is SP?

0 Answers  

WHAT IS THE REASON FOR THE GROUND PIN IS BIGGER IN SIZE COMPARING TO OTHER PINS?

13 Answers  

What range of speed can you get with the armature control method of speed control of d.c. Shunt motor?

0 Answers