Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


what is the difference between electrical & electronics

Answers were Sorted based on User's Feedback



what is the difference between electrical & electronics..

Answer / mahalakshmi

electrical deals with high voltages that is high inputs
where as electronics deals with low voltages or low input
circuits

Is This Answer Correct ?    0 Yes 0 No

what is the difference between electrical & electronics..

Answer / santosh

in electrical flow of current is through electrones and in
electronics carrier are electrones and holes. however holes
are generated by electrones in semiconductor electronics.

Is This Answer Correct ?    0 Yes 0 No

what is the difference between electrical & electronics..

Answer / rathinavel

ELectrical circuits
generate the power...
Electronics circuits
consume the power....

Is This Answer Correct ?    0 Yes 0 No

what is the difference between electrical & electronics..

Answer / venkat

The electrical means generating the energy


The electronic means that electrical energy safely utilized
and some controlling

Is This Answer Correct ?    0 Yes 0 No

what is the difference between electrical & electronics..

Answer / rambabu

electrical means flow of electrons
electronics means study of electrons

Is This Answer Correct ?    1 Yes 1 No

what is the difference between electrical & electronics..

Answer / amit

Electrical is
the study of
resistance,
inductance,
capacitance etc.
Electronics is
the study of
diode,
transister, IC's
etc.

Is This Answer Correct ?    1 Yes 1 No

what is the difference between electrical & electronics..

Answer / rakesh kumar panda

ELECTRICAL:-It deals with large units like "AMPERE,VOLT,K.WATT ETC".
ELECTRONICS:-It deals with small unit like "m.AMPERE,m.VOLT ETC".

Is This Answer Correct ?    1 Yes 1 No

what is the difference between electrical & electronics..

Answer / reza

electrical is a.c current-electronic is d.c current.

Is This Answer Correct ?    0 Yes 0 No

what is the difference between electrical & electronics..

Answer / maryam

In electronics we are dealing with Alternating current while
in electrical we deals with direct current.

Is This Answer Correct ?    0 Yes 0 No

what is the difference between electrical & electronics..

Answer / reema

electrical obeys ohms law but electronics doesn't obey ohms law....

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

What is the difference between Neutral and Earth

6 Answers   Bhel,


what is efficient load of transformer in percentage

4 Answers  


1)we r having one problem .one dry type transformer(6.6KV/433V)is taking high magnetizing current on delta connected HV side of "U" phase when compared to other two phases.could any body tell the reason why it is happening? 2)why CT secondary side protection core has got higher winding resistance when compared to that of metering core of same CT?

2 Answers  


sir what is the minimun earth resistance value of an industial bit and grid bit ? and Why?

1 Answers   Kirloskar,


why it is necessary to maintain frequency constant in a power grid ?

1 Answers   NTPC,


Energy metering: On the property I am renting, the supply voltage is 2 x 110 volts. These 2 x phases enter a energy meter which then exit the meter to over head lines to my house. Question 1. The meter is single phase 240 volts but is being used as 2 x phase(2 x 110volt), is this acceptable? if not, please give me the reasons. The meter details are as follows: 60Hz 15amp Imax 100 amp Kd 3,6 Wh/R 1 fase 3 hilos Model FX 231. I think it was manufactured in Brasil From this meter, the cables run along over head aluminum conductors,I estimate the cross sectional area to be 25mm diameter, but the neutral is only about 10mm square diameter, which cover a distance of 170 meters and then terminate with an underground cable of 65 meter length, total length = 235 meters. There must be a huge voltage drop over this length. This line is protected with 2 x 200 amp aluminum fuses after the meter, there is no main switch in the distribution board. These 2 phases connect directly onto 2 busbars. Surely the neutral should be the same size as the conductors if not more? Question2. What are your thoughts about this installation, should there be better protection, is the neutral too small? During the night, the lights dim then brighten all the time, this cannot be good for my electrical appliances. In my home, I only have a small electric geyser and fridge, my stove works off gas. But when i use other appliances like the washing machine or microwave oven, the light dim. The internal wiring of this house is done with solid hard drawn copper wires and of course, they have to be under rated. I am a retired electrician by trade, but not on the metering and over head mains side, my experience is on the factory maintenance side of things. Your expertise on these matters will be greatly appreciated. Please inform me how to rectify or make any improvements Kind regards, my power bill is very expensive, so I need to know how to bring it lower. Kind regards, Brian

1 Answers  


What is the exact minimum vale of voltage between an earth and netural which can damage or can do malfunction of the electronic equipments ? If this is mentioned in any book, pl.give reference.

0 Answers   Bhushan Power Steel,


how to find the resistance and gap volatage of the diode??

0 Answers  


What Should be the value of Vector Surge angle at Tripping and how to calculate it?

0 Answers  


Why hydropower is called renewable source of energy?

0 Answers  


What is mean by retrofitting of machine tool please brief.

1 Answers  


why generation voltages are 6.6kv or 11kv and why not some one give that stander that generation voltages are 5kv or 12kv?

1 Answers   AES,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)