Answer / p.gopalakrishnan

2/3 solenoid is not correct.
Generally we call it as 3/2 way solenoid valves
Ex: 3/2 way SOV,4/2 way SOV,5/2 way sov...
And in 3/2---- 3 indicates number of ports
i,e., input,output and exhaust.
2 indicates---- 2 positions.One position is to open(change
the position) the corresponding equipment and the second
position is to close (change the position) the
corresponding equipment.

Answer / amit

2/3 Solonied Valve Means 2 Way three Position Solonied Valve
For More Information please Go through.


http://www.engvalves.com/itemfiles/dv06actuation.pdf

Answer / r@kesh

There is no 2/3 solenoid valve.
Solenoid valve are of following types:
1. 2/2 solenoid valve
2. 3/2 solenoid valve
3. 4/2 solenoid valve
4. 5/2 solenoid valve

Here top integer indicates ways or ports and bottom integer
indicates positions.

Answer / bhupendra singh

This is totally wrong answer because 2/3 is not correct ,3/2 is correct. First digit denotes way and second digit denote Position.In any cylinder maximum two position possible first is Open and second is close,no chance for third position.If create third Position that means this will be middle if this position have that means the cylinder is jammed.

And way means Input,out put and Exhaust ports

Answer / s.selvakumar

one inlet,one out put one exhaust called 2/3way solneiod
valve.

Answer / rajiv sirohi

2/3 means this solenoid valve have 2 way and 3 ports. one
port is inlet, second is outlet and thisrd is exhaust. now
by these three port 2 combination are formed as (1) from
inlet to outlet (2) from outlet to exhaust. thus this
solenoid valve have two ways.

Answer / mahesh

It means 2 way 3 port solenoid valves.

Answer / jagdeep singh

two position and three input outputs. ....or two states
...three ports..

We Have Two Field bus Pressure Transmitters of Different Sensor Range (I.E One is of Lower range and Another is of Higher Range).Is same Process Line. My Question is Can i provide Saturation Limit to my field Bus Transmitter as We can provide Saturation current limit to HART Instruments. As During Low Pressure Both Working OK ,But During High Pressure, transmitter with Lower sensor range Goes to Fault mode as Beyond its Sensor Limit it can Measure, So may I provide Saturation point Some where to Suppress This Fault during High Pressure.

0 Answers   OPaL,

How to decrease opening & closing time of on/off valve?

0 Answers   UPL,

A length of steel pipe is used to carry sea water to a desalination plant. An adequate corrosion allowance must be specified and indicated in the piping specification, which affects the _________________________ of the pipe

0 Answers  

What is critcal speed. what is resonant frequency. why we want to cross crtcal speed on higher RPM (early).

0 Answers  

How to Calibrate Flow Switch in field

0 Answers  

is here anybody who knows how to calibrate the pressure transmitter? ONLINE

5 Answers  

What is the difference between PLC-HMI and DCS as each function of DCS based system is possible in PLC ?

2 Answers   Lucky Cement,

What is the formula of vabration sesore. i mean how to covert mils to volt plz share if any body knows   very argent : my mai is merajalam143545@yahoo.com

0 Answers   Samsung,

why would you like to join our company

0 Answers   Aramco,

What are the charecterstics of control valve.

2 Answers  

What types of thermocuple are mostly used?

6 Answers  

what is skin type thermocouple? how it is installed? what is the difference b/w thermocouple & skin type thermocouple? what is gounded & non-grounded thermocoplle? what is the diff b/w these two?

2 Answers   KazStroy Engineering, PSU,