Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


where do you give the 4-20 ma i/p in a MIL control valve?

Answers were Sorted based on User's Feedback



where do you give the 4-20 ma i/p in a MIL control valve?..

Answer / s

we can give 4-20 mA either to externally mounted i/p or
intergrated i/p cum positioner in MIL control valve.

Is This Answer Correct ?    7 Yes 0 No

where do you give the 4-20 ma i/p in a MIL control valve?..

Answer / gsn murthy

the input of the MIL control valve normally in I/P (current
to pnuematic convertor) or direct mounted of E/I.

Is This Answer Correct ?    6 Yes 1 No

where do you give the 4-20 ma i/p in a MIL control valve?..

Answer / sagar gadag hiranyakeshi suga

we give 4 to 20 ma i/p in positioner(in built
current/pressure transduser)

Is This Answer Correct ?    4 Yes 3 No

Post New Answer

More Instrumentation Interview Questions

Tyes of interface level measurement and how to use that technique for interface level measurement,

0 Answers  


explane hart protocol? what is its advantages.

3 Answers   Jindal,


What is mean by Ethernet, Device net and Control net? For what application we are using these?

4 Answers  


What is DCS and PLC scanning time?

5 Answers  


control panel design guidelines

0 Answers  


OBJECTIVE TYPE QUESTIONS OF ANALYTICAL INSTRUMENTATION

0 Answers   Fauji Fertilizer, GSECL, NFL, Power Plant,


What is the Flow rate ?

2 Answers  


what will be the principle & application of dissoled oxygen analyzer at wast water treatment plant at oxidation basin & how it work?

1 Answers  


why do we use 4-20mA as o/p and why don't use 0-20mA or 5- 21mA?

3 Answers  


what is skin type thermocouple? how it is installed? what is the difference b/w thermocouple & skin type thermocouple? what is gounded & non-grounded thermocoplle? what is the diff b/w these two?

2 Answers   KazStroy Engineering, PSU,


Explain about P&ID diagram?

3 Answers   Technip, Toyo Denki,


What safety precautions you will adopt to work on Steam service control valve?

1 Answers   QAFCO,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)