Answer / shekhar kundena

8 to10 kg for 1MT of reinforcements depend on structural design.

Answer / mohammed aijaz hussain, modi b

Generally 4.5 kg to 5 kg of binding wire is consumed for
binding 1 Metric Tonne of steel and for Columns 1.5 kg is
consumed.

Answer / vikash sharma

one ton m.s tmt bars using bending wire quantity's "12.5kgs"

Answer / bilal khan

As per standard knowledge in all over the world we use in 1 ton 10kgwire only.

Answer / simhachalam

One MT Steel is required 9- 13 kg of binding wire

Answer / ananthbathmanaban

approximately 100 kg of steel required 1 kg of binding wire is required...so for one tone 10 kg of binding wire is required....

Answer / neeraj kumar

go through with relevent is codes and cpwd specification,
normally it is 7kg per tonne in all the dias and all
locations.

Answer / partha pratim panja

As per Joglaker (Quantity Surveyor Book) it is mentioned as 
for every quintal of steel reinforcement ( 1 quintal = 
100kg) 0.9 to 1.3kg of binding wire is required




for 100kg of steel reinforcement = 0.9 to 1.0kg of binding 
wire (18 swg)




for 1 tonne (1000kg) = 9 to 1 kg binding wire will be 
required 

Answer / deepak n.baviskar

8to10 percent of total steel

Answer / shyam sundar mondal

it depend on dia of bar 8mm to12 mm dia road 6-8 kg /t
and 16-25 mm dia of bar 2.5 - 3 kg/t

the water is flowing through a velocity of 1.5m/s in a pipe of length 2500m and dia 500mm. at the end of pipe a valve is provided. find rise in pressure 1. if the valve is closed in 5 seconds. 2. if the valve is closed instantaneously. take value of c = 1460m/s, pipe to be rigid and bulk modulus of water - 19.692x10' n/sqcm

0 Answers   UPSC,

How much used for sand per square meter in 12mm Thickness

1 Answers  

what is the water cement ratio of 1:6 and 1:4 cement sand mortar. reply soon

0 Answers   Simplex,

Design a built-up column carrying an axial load of 1200 KN. Its length is 8m and it is effectively held in position at both ends and restrained against rotation at one end. Assume yield stress of 250 mpa

0 Answers  

How many cement bags of 50Kgs will be required for 2600sqft terrace with thickness of 5".

7 Answers  

What is the Requirements of indoor & outdoor Substation Construction? What is the main Safty Requirements for SubStation Construction?

1 Answers  

what is mean by shear resistance in concrete?

3 Answers   CCCL, Noble Consolidated Glazings, Sobha Developers,

Pls help me to arrive the rates for centering shuttering for highbay using H-frames?

0 Answers   Akshaya,

in 1:2:4 concrete, spcify 1,2 and4 as towhat they indicate?

2 Answers  

use 1:1.5:3 concrete footing size 9'9" *9'9" and square 12" and also trapezoidal 22" use of 4 columns. calculate how much amount f concrete use. and also tell me the details about course aggregate and fine aggregate and cement bags use .(note; 20mm coures aggregate use)

1 Answers   CMS,

in construction feild make the column rods are uneven ( e.g 1 column we have 6 nos of bars that 6 nos of bars are varrious level- 1 bar 10';2 bars 9';3 bars 8') what is resion to put different level if difference are required or not?

3 Answers  

What is the difference between tor steel and tmt steel?

0 Answers