Answer / prachi

pile foundation is the type of deep foundation. if their is
blake cotton soil is available and the hard strata is at
the depth of more than 5m and also when high load is
comming on foundation then this type of foundation is used.

Answer / karwan dartash

the pile foundation is a column in the ground taking
foundation loads to deep underlying soil strata,
generaly used where sub soils near the ground are weak or
water table is high.
pre-cast concrete, tubular steel and timber can used in
pile foundation.

Answer / joe

Piled foundations can be of various types. They
can be used to transmit the loads from the foundations
through weak, compressible,
or unstable strata, to firmer ground beneath (end
bearing piles). In
clay and other cohesive soils piles can be used to
distribute the loads
into the ground through the friction forces along the
length of the pile
sides

Answer / atanu cool bhuniya

Piling is a technique used extensively by contractors to set a deep foundation for structures such as buildings. By driving and embedding piles of wood, concrete or steel into the deep soil of the ground, the piling contractors are able to provide a strong support to the building structure at the foundation level - a pre requisite for any construction project.

Factors such as the size, capacity & scope of the project, the condition of the soil immediately beneath the ground, and space required for rigging, all need to be taken into consideration before beginning the piling process. As opposed to a shallow foundation, a deep foundation is used to transfer the load of the structure to the deeper, stronger layer of the soil which has a high bearing capacity and can take the load, thus supporting the structure well.

The commonly used Piling materials include wood, concrete or steel - precast concrete piles, vertical columns of wood, steel sheet piles & timber piles etc.

Answer / mohammed

pile foundation is the similar type foundation compare to
isolated or combined foundation . the things is we r using
in soft soil to provide better and better load bearing . Do
we require any shuttering if s u then what type

Answer / piya

a special type of foundation that enables a structure to be
supported by a layer of soil found at any depth below the
ground surface.

Answer / vijayakumar

pile foundation is used for smooth soil foundation it may
used for structure design

Answer / vijayakumar

the parts of structure used to carry and transfers load of
the structure to the bearing ground locate at more ground

Answer / balakrishna

phile footing is the deep foundation. This one can be using
for soft soils and sandy soils,river areas can be bearing
capacity will be low .
the phile footing can be load transfer above the ground
level to below the ground level.

Answer / neeraj sahu

pile foundation is that type of deep foundation in which the load are taken to a low level by means of vertical members which may be of timber,concrete or steel.multi-storeyde building are invariably founded on end bearing piles so that the settlement are minimised.

Why do you want to work here

0 Answers   Ramos Construction,

What is the difference between engineering stress and true stress?

0 Answers  

WHAT IS MEANT BY ZERO VALUE IN QUANTITY SURVEYING

1 Answers  

lap length formula

7 Answers  

how the find the quantity of water used to make 1 cubic meter concrete mortor

1 Answers   Appco,

how many types of admixters are used for C.C. Road works

1 Answers   CADS Software, IVRCL, PSK,

Why I-section is preferred to channel section?

7 Answers   Engineers India,

how can we calculate the cutting length of 10,12,16,20 and so on iron bars for 45 digree and 90 digree bents plz tell me if there is any formula or tabel to find it

14 Answers   Anukampa Group, AZ Engineering, L&T, Navayuga,

advantage and dis adventagesof using crusher dust insted of sand in rcc works

3 Answers   Descon, DLF,

how much quantity of 1.5" nails and 2.5" nails are required for conventional formwork shuttering?

0 Answers  

1 bundle=how many rods s there? and what is the length of each rod

2 Answers   Sobha Developers,

For plate load test why we are applying pressure 3 times the proposed allowable bearing pressure? Is there any supporting standards for this?

0 Answers   CDM Smith,