Answer / jale singh yadav

FOR IONIZATION OF GAS IN TUBE LIGHTS, IT REQUIRES HIGH
VOLTAGE NEAR TO 1100V OR 1200V ACROSS ITS TERMINALS.
STARTER HELPS CHOKE COIL FOR GENERATING THIS MUCH OF
VOLTAGE ACROSS THE TUBELIGHT TERMINALS FOR SHORT TIME
PERIOD SO THAT IONIZATION CAN HAPPEN INSIDE THE TUBELIGHT.
STARTER CONTAINS BIMETLIC CONTACT.AT THE TIME OF STARTING
IT WILL BE NORMALLY CLOSED & AFTER SOME TIME(SHORT TIME) IT
WILL OPEN & DUE TO THIS OPENING AS PER LANZ LAW CHOKE COIL
PRODUCE HIGH VOLTAGE ACROSS THE TUBELIGHT TERMINALS.

Answer / abdul nazir

Starter is used to help the choke to produce "self
induction". I will explain little briefly.
initially we need 1000v to start the tubelight,so one chohe
was connected series between the tubelight & other end of
the tube light was connected with starter.
In this starter inside it contains one bimetal strip(open
position)& parallel connected with one capacitor,inside the
starter full of argon gases.
initially the supply will go through the choke,tube light &
starter.
Already starter inside bimetal strip was in open condition
so supply will not pass it, inside argon gases are present,
so arc will produce between the bimetal strip & it will
close the ciruit(due to heat), so supply will pass throug
it, after then bitmetal stip getting cool and it will open
the contacts.
Immediately the choke gives 1000v due to self induction, so
inside the tube light ionsation was happens & start the light.
why capacitor is used inside the starter? To avoid the Radio
interference.(In our home television or radio is working at
that time if we switch on the tube light little bit noise
will come from the tv or radio, if the capacitor was not
there the noise will be very more this is called radio
interference.)

Answer / sam khanji

The main reason for the starter is to provide the spark
inside the tube which ionizes the Nion gas inside the tube.
The Nion's electrones at the last orbit will jumb to the
next orbit providing light.
the starter contains a capacitor with a very low
capacitance and has the ability to discharge quickly.

Answer / oarhe ize

Is to increase the starting current that can make the tube
to come up.It contains capacitor.

Answer / dharma

it to increse starting current , it require for tube lite
for initial. it contain bi-matalic strip.capacitor is also
connected for improveing power factor.

Answer / gunjan

Tube light requires two things to function . Very high
starting voltage , and high voltage to continue the
operation . The starter is a circuit which breaks at
regular intervals . When you break a circuit and start
again , high voltage spark takes place . This voltage is
further amplified through the choke which is a
transformer . Thus at the beginning the starter gives high
voltage sparks . Due to this the current begins to flow
through the tube and the tube begins to glow. Once the tube
starts , the required voltage to sustain is quite low ,
which is provided by the choke .

Answer / bhusani saikrishna

Tube light need
nearly above
1000v across
the two end
terminals .but
our supply
voltage is only
230 v.so we
need to step up
the
voltage.this
step up of
voltage is done
by the choke by
the process
called
selfinduction
and this
selfinduction
to happen
startor help
the choke.

Answer / santhosh kumar .k.m.

it is only used for starting purpose.it is used to help the
choke to produce self induction.

Answer / chawla

starter is nothing but a circuit which breaks at regular
intervals.breaking a circuit and again starting again leads
to high voltage spark which is one of the requirement for a
tube light.

Answer / abdul wahab

FOR IONIZATION OF GAS IN TUBE LIGHTS, IT REQUIRES HIGH
VOLTAGE NEAR TO 1100V OR 1200V ACROSS ITS TERMINALS.
STARTER HELPS CHOKE COIL FOR GENERATING THIS MUCH OF
VOLTAGE ACROSS THE TUBE LIGHT TERMINALS FOR SHORT TIME
PERIOD SO THAT IONIZATION CAN HAPPEN INSIDE THE TUBE LIGHT.
STARTER CONTAINS BIMETLIC CONTACT.AT THE TIME OF STARTING
IT WILL BE NORMALLY CLOSED & AFTER SOME TIME(SHORT TIME) IT
WILL OPEN & DUE TO THIS OPENING AS PER LAN'S LAW CHOKE COIL
PRODUCE HIGH VOLTAGE ACROSS THE TUBE LIGHT TERMINALS.

For an 100kw generator, only 50kw of load is connected. will the generator generate only 50kw or 100kw. if it generate 100kw what happens to rest of the 50kw. what happens if we connect more than 100kw of load?

8 Answers  

Dear sir, In our plant have Station Transformer having capacity,i want to know, why LV side 40 - 40MVA is given? & how we can get 6.3 KV supply from tertiary(i.e. Open delta connection), Vector Group YNyn0 - yn0 +d MVA Rating 80MVA / 40 - 40MVA + 26.7MVA Voltage rating 420 (Tap range +6,to -10)81.25% /11.5KV - 11.5KV +6.3KV

0 Answers   Bhel,

I WANT TO KNOW LONGFORM OF CT/PT USEDIN POWER PROJECTS OR HT SWITCH YARD.

7 Answers  

is it possible to minimize the copper loss?

2 Answers   Coal India, TATA,

Sir we are using 250 kva DG its Diesel consumption 25 lits / hrs maximum load 160 kva now how to calculate units/ litres

1 Answers  

What is the Full form of Rccb,MCCB,

11 Answers   Marriott, Maruti Suzuki, MCB, PCC, RCCB, Torrent Pharma,

What is a formula to decide the size of the cable of the star delta motor ( From Contactor to the motor 2 runs )

4 Answers  

what type of insulation is used for over head lines?

4 Answers   NTPC, WS,

can anyone tel me what is competency of electrical supervisor??

2 Answers   ONGC,

how many joint can done in HT line and what is life of the joint

0 Answers   Micro Labs, Reliance,

how the alternator transfere mechanical energy to electrical one ??

3 Answers  

"TRANSFORMER MODELING AND ANALYSIS" MEANS WHAT AND WHICH TOPICS U READ IN THIS

0 Answers