What will be the capcity of 3 phase DG set require for 25 KVA single phase lig

Categories >> Engineering >> Electrical Engineering
Suggest New Category

What will be the capcity of 3 phase DG set require for 25
KVA single phase lighting load?

Question Posted / satish

7 Answers
17867 Views
Supernova, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What will be the capcity of 3 phase DG set require for 25 KVA single phase lighting load?..

Answer / mrfbdr

Approximately 3-Ph 10kva Diesel generator will be enough
considering future loads too.

Is This Answer Correct ?

9 Yes

6 No

What will be the capcity of 3 phase DG set require for 25 KVA single phase lighting load?..

Answer / b.dhanasekaran

dg set we normally connect 75% of it,s capacity of dg, so
in lighting load single ph is 25 kva/3=8.33kva,
so nearest 3 phase dg is 15kva,
we can use 75% so 11.25 kva lighting load @ 3 phases you
can connect.

Is This Answer Correct ?

1 Yes

3 No

What will be the capcity of 3 phase DG set require for 25 KVA single phase lighting load?..

Answer / mel holmes

A 75kVA 3-phase generator is required to supply a 25kVA
load.
Consider a 75kVA, 400V, 3ph, 50Hz, 0.8pf DG set.

Full load current is 108A

A 25kVA 1ph load will require 108A.

Is This Answer Correct ?

0 Yes

2 No

What will be the capcity of 3 phase DG set require for 25 KVA single phase lighting load?..

Answer / rajiv garg

25kva dg also work but this will run 100% all time.
So u have to take some margin as DG mfg suggest as given
below.

for 25kva lighting load u have to use single phase
25/.8=31.25kva dg. available dg is 33kva

so u have to go for 33kva dg.

Is This Answer Correct ?

1 Yes

4 No

What will be the capcity of 3 phase DG set require for 25 KVA single phase lighting load?..

Answer / varma

can anyone explain more?
how can 10kva dg supplies load of 25kva(20kw)?

Is This Answer Correct ?

2 Yes

6 No

What will be the capcity of 3 phase DG set require for 25 KVA single phase lighting load?..

Answer / manju & raju

We can use 25 KVA Generator, but generator run as 100 %.

generator is over load.

pls we can use 25 KVA to 40 KVA Generator.

Is This Answer Correct ?

5 Yes

10 No

What will be the capcity of 3 phase DG set require for 25 KVA single phase lighting load?..

Answer / ashish

Here Your Load Is 25 KVA lighting load,& Incase Case Of
Lighting load The Load Diversity factor Factor Is Consider
as 1 so on Basis Of That We Must required 25 KVA 3Ph
generator ....but There May Be Possibiliry that All
Lighting Can Not Be ON.

Is This Answer Correct ?

1 Yes

7 No

Post New Answer

More Electrical Engineering Interview Questions

Why do we apply both Differential and REF (HV and LV) protection schemes on YNyn configuration of a transformer?

0 Answers WCC,

what is deferens between HT&LT DG

2 Answers

How much difference can there be between HT & LT KWH unit consumption at the same load?

1 Answers DLF,

why we calculate only 11kv 33kv and 132kv ... why not 10kv 20kv 45kv?

3 Answers Bhel, ISMT,

what is compatible kva for 3300 watts and why

1 Answers FoodBev,

What is TVSS Protection???

2 Answers Emerson,

at the time of starting back emf of a motor is zero.so how can it will start to run??

1 Answers

difference between servo motor and synchronous motor

0 Answers Hitachi,

kindly arrange to send me RRB Bangalore previous question paper for JE/Electrical and JE/Signal I am going to write exam on 2010

2 Answers

On what principle reluctance motors work?

1 Answers

132/6.6𝚔𝚟 𝚝𝚛𝚊𝚗𝚜𝚏𝚘𝚛𝚖𝚎𝚛 𝚗𝚎𝚞𝚝𝚛𝚊𝚕 𝚑𝚊𝚜 𝚘𝚗𝚎 𝚎𝚊𝚛𝚝𝚑 𝚙𝚒𝚝 𝚍𝚎𝚍𝚒𝚌𝚊𝚝𝚎𝚍. 𝙸'𝚟𝚎 𝚊𝚗𝚘𝚝𝚑𝚎𝚛 𝚝𝚛𝚊𝚗𝚜𝚏𝚘𝚛𝚖𝚎𝚛 𝚘𝚏 6.6𝚔𝚟/415𝚟 𝚌𝚊𝚗 𝙸 𝚌𝚘𝚗𝚗𝚎𝚌𝚝 𝚗𝚎𝚞𝚝𝚛𝚊𝚕 𝚝𝚘 𝚜𝚊𝚖𝚎 𝚎𝚊𝚛𝚝𝚑 𝚙𝚒𝚝 𝚊𝚜 𝚘𝚏 13/6.𝚔𝚟 𝚝𝚛𝚊𝚗𝚜𝚏𝚘𝚛𝚖𝚎𝚛?? 𝙸𝚏 𝙽𝚘.. 𝚃𝚑𝚎𝚗 𝚠𝚑𝚢??

0 Answers

How to Calculate The Neutral Earth flat design calculation for the Synchronised generator (Gen 1-650Kva, Gen 2-725Kva

0 Answers

For more Electrical Engineering Interview Questions Click Here