Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


when we start the tube light, then it takes initially 1100
volt, after glow it takes 120 volt?(when we give 220 volt a.c.)

Answers were Sorted based on User's Feedback



when we start the tube light, then it takes initially 1100 volt, after glow it takes 120 volt?(when..

Answer / prakash gokhale

Normally bulb or tubes are filled up with some gases.
deionisation of such gases gives the light as a product of
collidation of gas particles. But for that deionasation
high energy is required and we use choke for the same.
Choke is a inductive device which takes more power for
starting.

Is This Answer Correct ?    2 Yes 0 No

when we start the tube light, then it takes initially 1100 volt, after glow it takes 120 volt?(when..

Answer / pritish

at the initial stage the voltage induced by the choke is nearly about 2000v due to the inductive property of choke and this high voltage is required to discharge the gasses from the filament of the tubelight. after the discharge id initiated it requires normal supply voltage to maintain the path for the gasses inside the tube.

Is This Answer Correct ?    1 Yes 0 No

when we start the tube light, then it takes initially 1100 volt, after glow it takes 120 volt?(when..

Answer / amarnath

In a Tubelight we have a Choke which is made of Copper or
aluminium coil and when power is supplied this choke acts
as an inductive load and for inductive load initial voltage
required to start is more hence it is so.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

How to calculate the load loss and no load losses of the power Transformer? i am having the following details : full load ct : in AMP HV :1676 ; LV:31.5 1800 KVA ;33KV/620 V for wind mill applications

2 Answers   ReasonSoft,


what is difference between differential protection and distance protection and how we calculate the sloop?

5 Answers   OPS, Power Grid,


It is used or not HT cable single core 630 sqmm in LT 3 phase capacitor bank which is used in PCC(power control center).

1 Answers  


How to know th details about an electrical Drawing ? Please mention the easy method.

0 Answers   Siemens,


What is the difference between synchronous motor & asynchronous motor

2 Answers  


what is the RMU and RMU system in sub-station(11kv,66kv.....)

2 Answers   Alstom, Torrent Power,


difference b/w bus bar and tie line?if possible explain with eg:

2 Answers  


When generator connected, the circuit ELCB exploded. What is the reson?

3 Answers  


WHAT IS LOAD CELL

0 Answers   AP, TATA,


WHAT IS THE CURRENT CARRYING CAPACITY OF 2.5/3 CORE HI TUFF CABLE,WILL IT SAFLEY CARRY 8.6 AMPS OVER 120 METRES,CAN YOU ALSO ANSWER WITH FORMULA FOR WORKINGS OUT ,THANK YOU 3RDYR APPRENTICE.

0 Answers  


in which base we defined the conductor is Dog type, Squirrel type, rabbit type, wolf type etc used in transmission line?

3 Answers   Bhel, CIL,


why core of transformer in square or rectangular why not in circle or ellipse if this what happens

2 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)