As per principle we say in three phase supply ,the voltage is producing by pha

As per principle we say in three phase supply ,the voltage
is producing by phase angle between two phase so two phase
is needed means then why we using three phase ?

Question Posted / kumar

2 Answers
4321 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

As per principle we say in three phase supply ,the voltage is producing by phase angle between two..

Answer / vijendra joglekar

As we know the sum of phase angle difference in poly phase
circuits will be 360 degree
i.e
Assuming that the phase R has maximum induced emf at this
instant the emf of other phase will be less then maximum value
when phase R is rotated by 120 degree in anticlockwise
direction phase Y will come in the portion of phase R and
its induced emf will be maximum further when phase R rotates
by 240 degree phase B will occupy the position of maximum emf.
Hence we have to use the three phase RY B for i mean when we
connecting poly phase circuits

Is This Answer Correct ?

0 Yes

0 No

As per principle we say in three phase supply ,the voltage is producing by phase angle between two..

Answer / baskaran.r

in a given frame size we can get any number of phases but 3
phases are high in utilizing the capacity without much
complications. in a 3 phase system the phases are separated
by 120 degrees. in a two phase system the angle between them
will be 180 degrees which is the same as single phase only.

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Electrical Engineering Interview Questions

why the generator will take 8 to 12 hours to start after it got interrupted due to technical problems in case of power plants.

1 Answers NTPC,

How i measured Bus bars weight without wighting ?

3 Answers Encom,

1 HP = how many Kva

5 Answers

Why we use cosine angle for calculating power factor not in sine angle ?

4 Answers

What is cable gland,why does use for?

5 Answers ABB,

What is rotating magnetic field?Discuss elaborately.

0 Answers

1. alternator has full load regulation of 4% when pf of the load is 0.8 lag, 1500 rpm. full load regulation of 1400 rpm for 0.8lag will be ________ ?? 2. torque angle of a sync m/c operating from a constt voltage bus is usually defined as space angle between _______ . 3. method most effective in finding out no load losses in large DC shunt motoris ______ . 4. current carrying capacity of fuse material depends on ______ . 5. coil has res. 10 ohm, inductance 1H. what wil be current after 0.1sec after switching on to a 500V DC SUPPL ? ? 6. effect of phase lag compensation on servo systems ___________ . 7. rotor of a dc machine is usually supported upon ______ . 8. DC motor is preferred to AC motor in which application ?? 9. 3 nos of 10:1 Xmer are connected in Star-Delta to supply a load at 230V.the supply voltage must be ______ . 10. voltage source produces max current in which circuit. 11. cal. power, if current and voltage are out of phase by 90 degree. 12. suitable length of Xmission line of power at 66 KV. 13. Which of the theorm helps in simple computation when the load across a ckt is varying ?? 14. what is the adopted line length for power Xmission of power by cables ??

5 Answers TATA,

What is the actual calculation for transformer short circuit test?.

0 Answers

single phase voltage 230 and Three phase voltage 450 why 690 voltage

1 Answers XYZ,

who to select a swicth fuse unit......?

2 Answers

what is the working of loss of excitation relay (40G)? how it is work?

1 Answers

What is the formula that shows relationship between voltage and speed in an induction motor

2 Answers

For more Electrical Engineering Interview Questions Click Here