Exapain Deatails of the PID controlller

Question Posted / bhagwagar

4 Answers
10290 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Exapain Deatails of the PID controlller..

Answer / jignesh parekh

A meaning of pid controleer is propotional integral
derivatives.
in general, it is related to field parameters which comes
in dcs system and for this all parameters such as
flow,temperature,level,etc, we have to fine tuning to all
parameters ,so they will be set in dcs system and also
operate the field insrument as per the requirement of the
plant.
its basically control feedback parameters.

Is This Answer Correct ?

16 Yes

7 No

Exapain Deatails of the PID controlller..

Answer / m.ramtarkam

PID controller is used for control of any process parameter
in all types of Industries.PID stands for
Proportional,Integral and Derivative.A basic controller
comprises of three components i.e Process variable ,
setpoint and final control output.
There are many types of controllers such as cascade ,
remote set point,feed back , feed forward etc.
Proportional = 100 / xP ( unitless)
xP = gain
Gain = change of output/change of input ( unitless)
Integral : the time taken in seconds for a process variable
to travel one proportional band is called as integral value.
( unit seconds)
Derivative : rate of chage of output is called as
derivative (unit seconds)

Is This Answer Correct ?

8 Yes

4 No

Exapain Deatails of the PID controlller..

Answer / elsayem

pid controller stand for proportional integral and
derivative
it is afeedback control
proportional some times called gain

Is This Answer Correct ?

10 Yes

7 No

Exapain Deatails of the PID controlller..

Answer / rajesh

PIDcotrol is mostly prefered in industries for process
control.it have three elements proportional,integral,diff,p
element is used to produce the contol o/pbased on present
error i/p,integral is used to avoid offset,derivative is
used for change in error i/p.pid has the advantages of all
three elements

Is This Answer Correct ?

2 Yes

0 No

Post New Answer

More Instrumentation Interview Questions

What is open loop and close loop?

4 Answers L&T, Pearl Distillery,

what is the name of thermocople element cable from field to pannel end?

3 Answers

If a flow transmitter (magnetic type FT) that can measure flow and temperature, then why in some industries people use flow transmitter and temperature transmitter in the same line 1 after another? Even after 1 single flow FT is capable of measuring flow as well as temperature.

1 Answers Process Control Technologies,

what is the difference between Digital output DO signals /Commands for start/stop and Solenoid valves ??

1 Answers

is manifold required for an integral orifice meter?

2 Answers

Why integral control mode call Reset controller?

1 Answers

1. How many output signals do wew have in process control? 2. Could you write down the names of the pre-commissioning and commissioning stage test instruments and explain them (more than 5 items)? 3. What is the first step to commission a transmitter on service? 4. What is RTD? 5. Find the output value in MA of a temperature transmitter (RTD Type) at 120degree celius? 6. What is the O/P signal of a pneumatic transmitter? 7. What is the O/P signal of an elctronic transmitter? 8. What is the close loop and open loon?

4 Answers

what is start up vent valve ? why it is used in boiler?

8 Answers ACC, Bhushan Power Steel,

Which type of pressure can be measured by primary elements?

0 Answers

Instrumentation symbols interpration, P& ID, Logic diagram analysis, Electrical drawing analysis.

0 Answers CCIE,

what is procedure of calibration of remote seal transmiter, botom to top flanch 850mm, fluid liquid density .73, transmiter fixed on a fractionation colum, under vaccume 10mbar

4 Answers

what is difference b/w the solinoid volve and autodrain?

3 Answers

For more Instrumentation Interview Questions Click Here