Answer / venkatesh sk

below 5hp motor used dol 5to 15hp motor used stardelta
starer

Answer / pawan dahiya

DOL using gange normal used 5HP and 5HP to above used in
star delta. Because 5 HP above value without star delta
motor/pumps starting time requied power(yani three gunaa
reating ki)

Answer / prakash suhane

There is no hard N fast rule which state the range of star
delta and DOL starter, we have to keep in mind fallowing
points during configuration of DOL starter.
1) Motor should not be of very high rating.
2) Starting torque (reqd to start motor)is not very high.

apart from above case we should use star delta starter.

Answer / deny fernandes

dol for 5hp and above 5hp star delta

Answer / nani

Now a days we are using DOL starter up to 3ooKw, it can
possible, already we are working in this system.

Answer / pawan dahiya

Normal Dol Rang less then 5 HP and Star Delta Used Normal
5 HP to 15HP

Answer / rajkumar saini

below 5 hp using DOL starter & above 5HP using star delta
starter

Answer / bikash bhagat

the range of using dol starter is under 5 hp & above 5 hp we can use star delta starter because when we start the motor the starting current is inreases 5 to 7 times than the rated motor full load current so it should effected the motor thats why above 5 hp we use star delta starter

Answer / rangaraj

dol starter is us 5hp motor(3.5kw)in direct current.star delta starter is us above 7.5hp starting current high in star and delta delta reduced 3-4 times voltage.dol connection star and delta connection delta.... rangaraj015@gmail.com

Answer / pawan

Till 5HP motors we use DOL starters . If we use beyond it,there will be a drip in the mains power supply.. Beyond 5HP, star delta is use as firstly motor operate in delta and thus its starting voltage is less(which is req. as in starting no back emf is there) after an instant it start operating in star as now motor has developed sufficient back emf to counter the voltage. Now the current is less(I/root3) as less current is beneficial reducing losses.. Now the ques. arises why only 5HP?Why not 5.2 or 5.5? The answer is its just a standard value.When it is tested beyond 5HP, drip is showing.. Thus the value 5HP.. Also motor are not available as 5.2 or 5.3 HP..So the standard value taken is 5HP...

auto reclosing scheme for radial ehv feeder is to be implemented or not?

1 Answers   State Board,

will we get shock from dc?

12 Answers   L&T,

Practical condition in 400KV Sub station:- Breaker(open) , isolator(open), Earthing (close) at both end e.g A & B. Now Open A Stn Earthing than Open B stn Earthing (Which have a 50MVA reactor) , AND suddenly show R,Y,B phase 704KV,573KV,118KV respectively. Que is without closing of breaker how it is possible.???? My Whats app No:07621840498 for Further Discussion. Pls experts suggest.

0 Answers  

How to calculate pitch, gauge of winding wire, and No. of turns for 30HP, 3 phase, 4 poles 50Hz, 380V induction motors

0 Answers  

What is the function of Antipumping Relay and Lockout Relay?

1 Answers  

What is emperical relation.Name few of them which are used in electriacl engineering?

1 Answers  

How can get electrical c licence.Now i am working in spining Mill , transformer capacity 2750kva. Sanction demand 2250kva. Please advise me . My contact no 09944226823

5 Answers   Pace Power Systems, VRVS, VSJ Industry,

How PADO software increase the efficiency of power plant?

0 Answers   Avalon, SVS,

What is the range of efficiency of thermal or steam power plants? Why it is so low?

2 Answers  

what are the differenc between vcb and sf6 breakers

7 Answers   Google,

How do you calculate the actual power consumption of an inductive load appliance. Say, a deep freezer of 200watts

0 Answers  

a voltmeter shows 100v..wat is to be done to make it read 150v.

7 Answers