WHAT ARE THE DFT AND RMS MEASURMENTS PRINCIPLE IN NUMERICAL
TECHNOLOGY OF POWER SYSTEM ?? WHICH IS BETTER IN WHICH
QUANTITY MEASURNMENT??



WHAT ARE THE DFT AND RMS MEASURMENTS PRINCIPLE IN NUMERICAL TECHNOLOGY OF POWER SYSTEM ?? WHICH IS..

Answer / otto

RMS
The AC component is the effective mean value of the positive
and negative peak values.
RMS is used in applications where the effect of the DC
component must be taken
into account.
DFT
In the DFT mode, the fundamental frequency component of
the measured signal is numerically calculated from the
samples. In some applications, for example, it can be
difficult to accomplish sufficiently sensitive
settings and accurate operation of the low stage, which may
be due to a considerable amount of harmonics on the primary
side currents. In such a case, the operation can be based
solely on the fundamental frequency component of the
current. In addition, the DFT mode has slightly higher CT
requirements than the peakto-peak mode, if used with high
and instantaneous stages.

Is This Answer Correct ?    4 Yes 1 No

Post New Answer

More Electrical Engineering Interview Questions

What is a captive power plant?

2 Answers  


what is the difference between an alternator and a synchronous motor

0 Answers  


what is the suitable voltage of transmission line to transmit 10000w power through 250 km. (a)11kv (b)33kv (c)66kv (d)132kv ]and please tell me whats the logic behind it

7 Answers   ONGC,


What is the advantage and disadvantage of dry type transformer?

5 Answers   Bhel,


how to find out 3 phase complex power in per unit in unbalanced system?

0 Answers  






what are the ratings of sockets?

10 Answers   L&T,


what is the safe meggar values for motor, transformer HT, LT and Cables? IF we want to replace I/C bay at our 220 kv substation which is of 140 mw load capacity bay to be replaced by 400 mw capacity bay.other than CT(1200/1) what are the other equipment i have to replace. why we generally use 3.5 core cable or in other word 1/2 core for neutral and also confirm me that in balance conditiob(3 phase)current in neutral will zero

0 Answers   Jindal,


What is the basic principle of circuit breaker?.. I read that it works on electro-mechanical principle... Does it require both electric n magnetic conversion to act?

3 Answers  


HOW TO BUILD THE SINGLE PHASE TO THREE PHASE CONVERTER? CAN PROVIDE ME CIRCUIT..THANKS

0 Answers  


how to calculate no load losses units comsumed by transformer

2 Answers   MRF,


Why two nos. un-tensioned wires are placed inside the PSC poles used by powergrid in RGGVY works.

2 Answers   Bhel, Power Grid,


CALCULATE THE TOTAL VOLTAGE DROP AND SELECT THE CABLE SIZE IN MM-SQARE FOR A PANEL-262KW AT 110 METER FROM THE SOURCE SUPPLY , SUPPLY VOLTAGE 240/415

0 Answers   DEWA, Growth,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)