why rating of motor in HP?
Answers were Sorted based on User's Feedback
actually,the answer to this question is,the ratings of
the motor must be in watts ,since dependent on
power ,therefore by using the formula,
1hp=740watts, this enables the conversion in
watts.
just to avoid higher ratings we are in use of hp
Is This Answer Correct ? | 39 Yes | 16 No |
Answer / garima
b'coz motor rating depends upon o/p mechanical shaft
power/torque.thereof,it doesn't depend on electrical i/p power.
So it is rated in HP which is a mechanical unit.
Is This Answer Correct ? | 21 Yes | 4 No |
HP is non-SI units of power,
1 HP = 746 Watts.OR 1HP x 0.746 = kW
It was originally defined to allow the output of steam
engines to be measured and compared with the power output
of draft horses.
Practicaly all system measurements converts into Electrical
System for simplicity and easy valuable results
Is This Answer Correct ? | 14 Yes | 4 No |
I just want to say shortly,
KW or MW or W is used for meaning of Electrical Power.
and HP is used to meaning of Mechanical Power sometime it
also known as BHP (Break Horse Power)which is found on the
shaft.
more info and online Earning:
http://a2zengineering.blogspot.com/
Is This Answer Correct ? | 10 Yes | 3 No |
Answer / nikunj thakkar
there is one simple question that why we are using KW and not HP?
ANS:-
as we know that is HP is unit of power in mechanical sometimes it happens that we say that am heaving 150W motor
and in market it the minimum size is in 0.5HP as said in above answer it is easy to calculate KW power of motor
second we are using motor to do mechanical work not electrical work so it would be easy to say that we heaving motor in HP not in KW
Is This Answer Correct ? | 7 Yes | 4 No |
Answer / jagadish
i don't no sure but thinking practically motor giving mechanical power as output so we must put motor rating is in h.p(mechanical unit ). likewise if you see in transformer ,output is electrical. so it represented in electrical unit
Is This Answer Correct ? | 3 Yes | 2 No |
Answer / wasim
Stean engine or oil engine or motor are usually rated in HP
because these mation drive another machine soits power is
termed as mechanical power hence it is rated in hp.
Is This Answer Correct ? | 1 Yes | 1 No |
The output of motor is mechanical not electrical
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / karthik raman.b
horse is the animal which run fast even its loaded so the
motor will drive the load without affect the speed of it. so
the motor power is compare with horse power.
Is This Answer Correct ? | 6 Yes | 9 No |
Answer / sivakoti
MOTOR MAKKING BY SPEED SO IT IS CALING HP.1HP MOTOR IS
LIFTING TO 746W.
Is This Answer Correct ? | 2 Yes | 5 No |
how to find the resistance
i am completed in B.E(Electrical and Electronics Engineering) with 8 months experience in Quality Control Engineer at Bharathi Industries,Coimbatore.
how do i commission a distribution transformer knowing all its ratings and transformation ratios?d
How much area is covered by a single lightning arrestor to protect object from lightning strokes ?
What is the advantage of Neutral graunding transformer insted of Neutral graunding Resistance in generating station explain briefly.
10 tube light connect in mcb breaker.one tube light is fault.so breaker is tribe.how fault is rectified.(using 3wire phase,earth,neutral)
what is the meaning of TPN
I want to put this query to SENIOR & EXPERIENCED ELECTRICAL ENGINEERS. 1)I want to know about the control circuit diagrams for control panels. I found it difficult to understand. Is there ant booklet through which we can learn the circuit diagrams? 2)I want to learn about conduiting, laying cables, preparing cable schedules and various techniques which is the part of building infrastucture(construction field). I don't have any experience in this area. I have experience in control panels only. that's why i am not getting any opening in building infrastucture (construction field).Can I get the job in this field as Trainee Engineer? How to enter this field? I need job in PUNE
generator(Deutz 550kv)is runing for 2 hours with load of 900 amp and then it goes in shutdown with alarm fault messege of speed fault although heirtz reading fixed at 50,what does that mean
Draw torque - speed curve and load curve of induction motor? mark operating point ?
what are the electrical components required for run the motor pump including safety components plz explain it how we can use such components .
sir, in a industry present pf is 0.54 pf 25hp power is there its want improve 0.9 pf. which suitable capacity capacitor is suitable please inform me.