Answer / rajkumar

lighting arrester is protect the power plsnt....its a low
impedance path..........
wavetrap is used to separate the carrier signal and
frequency.......

Answer / sandhya

lightining arrestor gives low impedence path for the over voltages at time of lightning strokes.....where as wave trap is used to give the high impendence path for the carrier frequency signal....

Answer / tapomay mondal

Lightning Arrester or LA is a protection device that is connected to the line in parallel.In stable system LA is working as a insulator. But when surge current travel through the line then it is worked as a conductor and pass the huge current to the ground.
For transformer protection you can see LA in HV side as well as LV side. This protection is mainly for high voltage system.

Answer / nirmal karmakar

Lightning Arrester or Surge Arrester is a electric device
which protects the equipments from extra high voltage or
surge voltage. It provides a low resistance path for surge
voltage or high voltage. When lightning occures then for
micro sec a very high voltage produces which may damage the
equipments. So to protects such equipments LA connceted
Parally or shunt with equiments.Although it provides low
resistance path for EHV, so all surge voltages directly
grounded and equipment save from damage.

Answer / jeff brown

A line trap is a parallel L/C circuit that creates a low impedance at power frequency(60hz) and a high impedance at your desired carrier frequency. You will have a trap at each end of the line that utilizes a pilot scheme such as DCUB scheme. On a simple scheme, you will usually only couple your carrier signal to a single phase of your three phase system. If this phase was to become faulted to ground behind your line, say on your bus, the traps high impedance to your frequency would keep your carrier frequency from following the fault current to ground and essentially "trapping" your frequency on the line ensuring your pilot scheme operates correctly.

There is a surge arrestor located internally to the trap that passes very high current faults on the system to protect the C of the L/C. Circuit.

Answer / s madhukar

Lightning Arrester is a device used on Elctrical Power
Systems. It is used to protect the insulation of the
system.When a lighting surge travels along the power line
to the arrester, the current from the surge is diverted
through the arrestor in most cases to earth.
Wave Trap is a device used on Electrical power sysems. It
can descriminate the Power Frequency waves and power
communication waves and it reduce the noise and
interference from line.

Answer / rakesh kumar nayak

it is nothing but a register in which you have
record all the blue pictures.

Answer / rahul

Lightning Arresters___prevent lightning strikes to a
certain extent.
Wave trap__tuned Cicuit used to eliminate a particular
harmonic by tuning the circuit for that particular harmonic

What if high voltage side circuit breaker of a ehv transformer instead of lvcb? Kindly elaborate.

0 Answers   MSETCL Maharashtra State Electricity Transmission Co Ltd,

how give earthing conection to household equipment?

0 Answers  

What is a advantage of Self Reset Lockout ? On Fault breaker get trip & fault no longer exist then self reset lockout how inform us?

0 Answers   Bhad Engineers,

what is the meaning of DSL

4 Answers   Airtel,

what voltage generated earth tester meter when we testing the Earth point ?

1 Answers   Cognizant, CTS,

what is a pilot wiring and whys that called a pilot wiers

0 Answers  

Does the dg syncronization sucessful in practical.

2 Answers  

What do you mean by isolators and circuit breakers?

6 Answers   Bhushan Power Steel,

What is difference between 220v/50Hz & 120V/60Hz?

8 Answers  

Safety of dry type transformer

0 Answers   Icon,

In star delta Schematic can we connect OLR in delta circuit

2 Answers   ABB, Lanco,

For Electrical / and Electronic Systems, when we say efficiency is 80%, then what happens to other 20% from the Power consumption.? I.e. what happens to this?

1 Answers