Answer / yash

RTCC is Remote Tap Change Circuit is connected to OLTC of
Transformer through control cables. It raise & lower the
voltage as accordingly specified by controlling the motor
drive in OLTC electrically (and manually through Push
Buttons)
In RTCC an AVR (Automatic Voltage Regulator)is fixed to
maintain the output voltage level(raise & lower) by
controlling the motor.

Answer / sanketh

RTCC is a panel it should be place in the electrical room
for Remote Tap changing.It must Required while OLTC is used.

Answer / joy banerjee

In transformers Output Voltage can be controlled either by
Off Circuit Tap Changer (Manual tap changing)or By On -
Load Tap Changer-OLTC (Automatic Changing).

In the transformer with OLTC, it is a closed loop system,
with follwing components:

#1. AVR (Automatic Volatge Regulator- an electronic
programable device). With this AVR we can set the Output
Voltage of the transformers. The Output Voltage of the
transformer is fed into the AVR through the LT Panel. The
AVR Compares the SET voltage & the Output Voltage and gives
the error signal, if any, to the OLTC through the RTCC
Panel for tap changing. This AVR is mounted in the RTCC.

#2. RTCC (Remote Tap Changing Cubicle):This is a panel
consisting of the AVR, Dispaly for Tap Position, Voltage,
LEDs for Raise & Lower of Taps relays, Selector Switches
for Auto Manual Selection... In AUTO MODE the voltage is
contrlled by the AVR. I manual Mode the operator can
Increase / decrease the voltage by changing the Taps
maually through the Push Button in the RTCC.

#3. OLTC is mounted on the transfomer. It consits of a
motor, controlled by the RTCC, which changes the Taps in
the transformers.

Answer / arun babu.s

RTCC is " Remote Tap Change Centre " which is a
programmable device to control the output of the transfomer
thro'OLTC unit fitted in the transformer through control
cables.
The desired voltage will be achieved accordingly by
controlling the OLTC with respect to the tap position
through RTCC system.
The output voltage of the transformer is been maintained
through an inbuilt AVR (Automatic Voltage Regulator),which
continuously verifies the output power with the set /
programmed reference voltage.Which triggers the OLTC
accordingly.
Hence,by above said phenomena,the consistency of the
transformer output is been maintained.

Answer / rahul kumar

In transformers Output Voltage can be controlled either by
Off Circuit Tap Changer (Manual tap changing)or By On -
Load Tap Changer-OLTC (Automatic Changing).

In the transformer with OLTC, it is a closed loop system,
with follwing components:

#1. AVR (Automatic Volatge Regulator- an electronic
programable device). With this AVR we can set the Output
Voltage of the transformers. The Output Voltage of the
transformer is fed into the AVR through the LT Panel. The
AVR Compares the SET voltage & the Output Voltage and gives
the error signal, if any, to the OLTC through the RTCC
Panel for tap changing. This AVR is mounted in the RTCC.

#2. RTCC (Remote Tap Changing Cubicle):This is a panel
consisting of the AVR, Dispaly for Tap Position, Voltage,
LEDs for Raise & Lower of Taps relays, Selector Switches
for Auto Manual Selection... In AUTO MODE the voltage is
contrlled by the AVR. I manual Mode the operator can
Increase / decrease the voltage by changing the Taps
maually through the Push Button in the RTCC.

Answer / praveen

RTCC is Remote tap changer circuit, normaly RTCC panel will
be installed in Main panel room and will be connected to
OLTC ( On line tap changer) of the transformer through
control cable.There will be AVR in RTCC Panel to control
the secondary voltage of the transformer and AVR output
will control OLTC motor in Clock wise or Anty clock wise.
and also there will be selection in RTCC panel for Auto and
manual operation.

Answer / lalit pratap

RTCC full form is (Remote tap change Control) it's using in OLTC (On Load Tap Changer)installed transformers for voltage regulation controll.

Answer / rajeev

RTCC refers to Remote tap changer cubicle.

It is used to change the tap of transformer from LT panal
room whith the help of remote circuit.

Answer / ajay kumar singh

RTCC IS REMOTE TAPCHANGER CONTROL CUBICAL WHICH IS ESTABLISH IN CONTROL ROOM OF SUBSTATON, IT IS REQUIRED WHEN OLTC IS USE IN POWER TRANSFORMER,AVRR(AUTOMATIC VOLTAGE REGULATER RELAY)MOUNTED ON RTCC PANEL WHICH SET UP SECONDARY VOLTAGE OF TRANSFORMER FOR AUTO MODE ONLY

Answer / anand

RTCC IS REMOTE TAP CHANGE CUBICLE , WHICH GOVERNS THE
VOLTAGE CONTROL OF THE TRANSFORMER THROUGH AVR OR BY MANUALLY.

IT HAS ANNUNCIATOR (MICROPROCESSOR BASED PROGRAMMING)WHICH
ALARMS THE OPERATOR DURING THE FAILURE OF FAN ETC.

what i the full form of ABS 111 in transformer.

1 Answers   Birla, Ford,

What are the reason of unbalanced secondary voltage of HT transformer 33kv/6.6kv ? Incomming voltage is balanced.33kv each secondary voltage 6.6 kv 6.4 kv 6.4 kv At no load conditions.

1 Answers  

advantages and disadvantages of inverse definite minimum time RELAY

0 Answers  

What is hysteresis losses?

2 Answers   GMR,

TRANAFORMER RATING 500 KVA,33KV/433, SECONDARY SIDE SWITCHED ON ONLY CAPACITOR LOAD 140 AMS, PRIMARY SIDE HOW MUCH VOLTS INCREASE?

1 Answers   BPL,

why the value of k is more in shell typr transformers?

0 Answers  

What is the difference between IGBT and TRIAC?

3 Answers  

what effect on electrical equipment if PF is gone over 0.996 in leading when provider say that its keep in minimum 0.996lagging

3 Answers   ABB,

1.why motor rating in kw instead of KVA? 2.why alternators rating in KVA instead of KW?. 3.why transformer rating in KVA instead of KW?.

6 Answers  

what is AVP?

2 Answers  

resistance switching is used in case of- ? a. air blast CB b. bulk oil CB c. minimum oil CB d. all types of CB

4 Answers   HCL, SSC,

why we generate 11kv power supply in generating station?

1 Answers   DBG, NTPC,