Answer / gajanan

star delta starter is used to reduced starting current
taken by motor. for this first startor wdg made connect in
star and then in delta.

Answer / senthil

for reducing the motor starting current,initially motor
will take 4to 5 times of full load current,If we use star
delta it will reduce 1.732times of its torque as well as
current will reduce,motor will get safe

Answer / shyamkr

actually the main concept is to reduce the starting current.
initially stator windings are connected to the bus through
star connections it reduces the stating voltage to 1.732
times n hence the starting current.
after sometime ,when max.speed is achieved it has been delta
connected and the voltage applied at the terminals is equal
to phase voltage.

Answer / praful nandankar

Basically star delta starter is used to reduce the starting
current.When u'r connections are in star, the voltage is
reduced by 1/1.732 times.When the motor attains 80% of
speed, connections changed to delta.
praful nandankar

Answer / sennapparajan

The concept of star delta starter is to reduce the starting
current of motor. in star connection line voltage and
pahase voltage is same which is 230v.so srating current
normally reduced.

Answer / gunnam santosh

for an induction motor at starting current is very high
speed is small so initially reduced current is applied.for
star connected winding phase voltage is root3 times the line
voltage and for delta current is root3 times the line current
so initial current can be reduced by using delta and then
star during starting of the motor

Answer / jagadisha.n. bmsit

At the starting motor needs high torque to reach rated speed
so it will required more flux to get that torque hence it
takes more current from the supply, but the winding
resistance is too low to withstand this current.

we know that
in star phase current = sqrt(line current)
In delta line current = phase current

So current is reduced by sqtt(3) times in star so motor is
first connect to star and then delta

what diferent amoung three phase supply?

1 Answers  

What is a charge.?

4 Answers  

delta motor winding resistance I take normally single winding is 2.5, which value is came delta connection ie RY ?

0 Answers  

HOW TO FIND THE PRIMARY AND SECONDARY OF TRANSFORMER(IN OFF CONDITION) USING MULTIMETER? IS IT POSSIBLE FIND BY SEEING RESISTANCE???

4 Answers   Areva,

WHY TRANSFORMERS ARE RATED IN 11KV 22KV 33KV Instead off 10kv 20kv 30kv

5 Answers  

What is load boxes ?

0 Answers   AMIE, PEPL,

234 MVA Generator 3 phase Short circuit current Values required? Gen set Rating-234 MVA, Gen Voltage-18kv, PF;0.8, Xdv:23.5 %, Transformer Rating-18/380KV, 680MVA,Yndd1 two winding, Step up TR, ZT:35.50 %,X/R 4.33 Gen CB Position, CB open ,Disconnected open, Generator Running Voltage 18 Kv, Bi mistakes generator side earth switch Closed during that time short circuit current level in 3 Phase required, and how to test on site 234MVA Generator Short circuit current,

0 Answers   Jubail O&M,

Which fault is caused by lightening and thuderstorm a. Line to line fault b. Single line to ground fault c. Double line to ground fault

1 Answers  

How can we measure and monitor critical performance parameters of Diesel Generator Sets, both electrical and engine ?

3 Answers   Cologicx Systems,

What will be the effect of in HT XLPE 220 KV cable when one side of the Armour/cable ends are not grounded. Will there is difference between 3-phase voltages? like: if A. Both End of Cable grounded Phase Voltages:- V1=219 KV, v2=220 Kv, v3=220 KV. B. One End is grounded other is not: than Impact on Phase Voltages:- V1= KV, v2= Kv, v3= KV. Remain same or unchanged??

3 Answers   Jamshoro,

what is the name of oil used in transformer

11 Answers   Energy Pack, Genco,

can we do the star delta connection of capacitor for 3- phase motor starter.

0 Answers