Transformer's core is made up of which material and why so?
- 10 Answers
- 29120 Views
- ABB, NTPC, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / ranjith
t/f core is made up of silicon steel which is having low
value of steinmetz constant.this helps in the reduction of
the hysterisis losses considerably.
| Is This Answer Correct ? | 54 Yes | 5 No |
Answer / vinothbabu.k
cold rold grain oriented material....to minimize loss in tr
like eddy current,hysterise loss
| Is This Answer Correct ? | 27 Yes | 5 No |
crgo is used as core in transformers to reduce iron and
frequency losses. but now a days Ampourpose is using as a
core. b'coz its thickness is very less compared to crgo and
core losses also compared to less. but little more costly.
| Is This Answer Correct ? | 20 Yes | 1 No |
Answer / swapnil
Transformers for use at power or audio frequencies
typically have cores made of high permeability silicon
steel. The steel has a permeability many times that of free
space, and the core thus serves to greatly reduce the
magnetising current .
| Is This Answer Correct ? | 7 Yes | 0 No |
Answer / ashok mishra
it is made up of silicon steel stampings of approx. 3mm to reduse iron and core losses
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / mahaboob
T/F core is made up of crgo steel. beause it has good
permeability copared to other material. it's value is 1.2
| Is This Answer Correct ? | 6 Yes | 3 No |
Answer / brijesh
Transformar cor is made of The lemittion of selicon steel
or jermeniyam steel to decreeas the iron losses in the
transformar
| Is This Answer Correct ? | 3 Yes | 0 No |
Answer / pruthviabbur
transformer core is made up mainly by iron.viz it it
supports for magnetic path and for current also.
| Is This Answer Correct ? | 3 Yes | 2 No |
Answer / monalisa rout
softiron because it reduces eddy current loss
| Is This Answer Correct ? | 5 Yes | 10 No |
1.what is the funtion of chiller primary & scondary pumps. 2.what is the use of distribution lines & Types. 3.what is the use the thermal power stations & how much capacity.
what is the basis for selection of Protection CT class ? How anyone can decide whether to go for 5P10 or 5P20 ?
Can anybody tell me how to calculate(formula) earth flat size(for copper and aluminium).
How can eliminate noise problem inside temperature controller temp. variation due to contactor chattering problem.
what is purpose of using reactor in substations.
20 Answers Heavy Engineering Corporation Ltd HECL,
30 kVA and voltage 380/220VAC how to find out kA?
critical losses of transformer
Which motor connection is preferable star-delta or delta-star?
what is the transmission loss for electrical supply? specifically a large shopping complex where the grid is half KM away, what will the % of transmission loss? is there any transmission loss for captive unit generation for above set? thanks
What is ignition module of a CAT Gas Genset G-3508 Engine, Alternator SR4B Series. HOw its checked for correct functioning.Is it repiarable or replacable?
How to make two bulbs glow Alternatively?
What is cut-off rate?
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
