Answer / harsha

power means
voltage*current
power t/f(1-phase,3-phase)is designed to change amplitude
of high frequency pulses by the turns ratio and provide
isolation b/wcircuits
distribution transformer is used to change the voltage
levels ex:high to low&low to high
(step up t/f&step down t?f)

Answer / raj

Power transformers are used for transmission as a step up
devices so that the I2r loss can be minimized for a given
power flow.These transformers are designed to utilize the
core to maximum and will operate very much near to the knee
point of B-H curve(slightly above the knee point value).This
brings down the mass of the core enormously.Naturally these
transformers have the matched iron losses and copper losses
at peak load (i.e the maximum efficiency point where both
the losses match).
Distribution transformers obviously cannot be designed like
this.Hence the all-day-efficiency comes into picture while
designing it.It depends on the typical load cycle for which
it has to supply.Definitely Core design will be done to take
care of peak load and as well as all-day-efficiency.It is a
bargain between these two points.

Answer / narendra verma

in short we can say that power trans belongs to the voltae
ratings above the 33kv and distribution trans are for low
voltages.....
it is also right that the size of the power trans is much-
much bigger then the distribution trans, that is all bcoz
of the rating and the operating voltage.........

Answer / sakthi

there are two types of transformer 1. power T/R 2.
distribution T/R 1. power tranformer is using ii high
voltage tranmission
2. distribution T/R for low voltage transmission

Answer / sunshine

Power transformer is used with Current transformer.
There is only one power transformer at generating station only, but many current transformers.

This is to check faults and measurement purpose.

where as distribution transformer are every where for efficient power transfer.

Answer / manish mathuriya

above 200 kVA power T/F
below 200 kVA distribution T/F
greater the power ratting higher the efficiency.

Answer / ajit

one power transformers can be perform step up &step down
both but one distribution transformers can use either in
step up or step down

Answer / amit sharma

power transformer transforms all the negative power of
hu(man) body into fluid and brings(steps)it down through
penis to distribute it in vagina.
distribution transformer suck my dick.

Answer / anand

Powr transformer are used in transmission network to step
up/down voltage viz 440/220KV, 220/110 KV,33/11 KV and
generaly of capacity 1 MVA or more.
Distibution transformer as name implies are used in
distribution network and steps down voltage to.433 KV &
normally of capacity less than 1 MVA viz 11/.433
KV,33/.433KV

Answer / binay agrawal

power trafo is generally step up transformer,
distribution trafo is step down.

What do you mean by per capita requirement of electrical energy in india

0 Answers   Tech Mahindra,

can i know how to design overcurrent setting and earth fault for 11kv & o.433kv system assuming tx 1000kva.

2 Answers  

i want to syncronise 5 nos of DG. How? pls reply

3 Answers  

why we use carbon brush in exciter&genrator?

5 Answers   ABB, SMC,

can we light the mercury vapour (tube light)with out a 1).starter and 2).choke in our homes if yes explain how?

5 Answers  

what is droop control?

0 Answers   BARC,

what is the function of choke in tube

1 Answers  

A mass of 1200g is accelerated at 200 cm/s2by a force. The value of the force required is:(a) 2.4N(b) 2400N(c) 240 kN(d) 0.24N

0 Answers  

Am using an electronic digital display to see the RPM of ABB ACS 550 drive, which is showing negative value when the motor & drive in stop mode but it is showing correct value during the run mode. can anyone help me out??

2 Answers   Bala Power Solutions,

What is the megger value for ht

16 Answers   Electrical,

if we have 320KVA Genset kindly advice how much load we can put it.

0 Answers  

what is the difference between electrical & electronics?

4 Answers   JSW,