how can i communicate with non-national instruments device with pc via labVIEW

how can i communicate with non-national instruments device
with pc via labVIEW8.2

Question Posted / guest

3 Answers
12255 Views
Google, Mico, National Instruments, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

how can i communicate with non-national instruments device with pc via labVIEW8.2..

Answer / rupesh kumar

labVIEW when to used for control of i/o a data acquisition
card(6211) should be there in the server PC/working pc.

Is This Answer Correct ?

7 Yes

1 No

how can i communicate with non-national instruments device with pc via labVIEW8.2..

Answer / sivaprakash

either u can use a DAQ card or u can use VISA architecture
and communicate via serial port

Is This Answer Correct ?

5 Yes

3 No

how can i communicate with non-national instruments device with pc via labVIEW8.2..

Answer / subramanian.s

By using DAQ6008 or DAQ6009,We can easily connect the non NI
device to PC. But, Before that you should have an
information about what type of inputs and outputs required
means that whether it's Analog or Digital. It should be note
that DAQ only Accepts -10 to 10 volts.Further details ,
Please check with DAQ6009 Catalogue.

Is This Answer Correct ?

2 Yes

0 No

Post New Answer

More Instrumentation Interview Questions

what is the difference between auto tuning and manual tuning of controllers(eg:PID,PI,PD CONTROLLERS )

2 Answers GATE,

how to calibrate a control valve?

7 Answers Reliance, Telecon Systems,

why we go for pcbs

2 Answers

Sir, I am working as a Instrument Engineer in Grasim Industries. Can any body provide question answer for interview purpose

0 Answers Grasim,

How to calibrate DP tramitter in flow measurement application? consider my range of flow is 0 to 2000 kg/hr ? please give calculation of , How much pressure applied on low pressure side and high pressure side please give detail of calculation .... It so important for me please reply as soon as possible

1 Answers

what is HVAC?

1 Answers

what is the difference between plc and pc?

5 Answers ADI, NFCL, Wipro,

What is difference between flame retardant & flame resistance cable? Among which type of cable is used for ESD & Fire and Gas system application?

1 Answers

Which of the following instruments consumes maximum power during measurement?

3 Answers

HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME... SUPPOSE ,, I HAVE A CLOSE VESSELE TANK ( HEXANE MEDIA ) ,, I M USING ROSEMOUNT 2051 DPT FOR LEVEL APPLICATION .. ITS CALIBRATE RANGE IS.. . 0 TO 950 MMH20 ..I DID CALIBRATED DPT WITHOUT REMOVING IMPULSE LINE OF HIGH AND LOW TAPPING.. & WITHOUT DISTURB 3 WAY MANIFOLD..!!! BUT ,,, DURING CALIBRATION I SELECT RANGE BY HART LRV IS 900 MMH20 & URV IS 1300 MMH20 ,, BUT ,TANK LEVEL SOMETIMES 100 % AT 1100 MMH20 , SOMETIMES 1300 MMH20 ..IN THIS CONDITION .. WHOLE LOOP FAILED ,, MAIN THING IS THAT ,, HOW TO CUSTOME RANGE SELECT ?? AND IF I USED RANGE OVER THE ORIGINAL CALIBRATE RANGE ,,,THEN WHAT ERROR WILL BE COME ??? HOW TO ZERO CALIBRATION OF DPT... HOW TO ZERO TRIM BY MANIFOLD ?? AND FOR TANK LEVEL PURPOSE ... WHICH UNIT I CAN USE ??? IS THERE ANY CALCULATION OR CALIBRATION .. IF YEH .. THEN PLZ JUST GIVE ME CALIBRATION STEPS FOR DPT.. THANKS YOURSSSSSSS

1 Answers Torrent Pharma,

can we copy the software from a transmitter using hht(hart 275) ?

0 Answers

Ple give me "INDUSTRIAL INSTRUMENTATION AND CONTROL S.k. Singh 3th edition" Solution manual to self-Check Quiz and chapter-wise PowerPoint Slides. Home web-site not available... Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Thanks for all...

0 Answers

For more Instrumentation Interview Questions Click Here