Answer / ali raza

There are different type of fuses HRC is also
one of the type and it stands for " High Rupting Capacity".
This type of fuses normally used where some delay is
acceptable for protecting the system.

Answer / mandy

We manufacture HRC fuse,www.cncelegroup.com

Answer / suresh

high rupture capacity . it used the DB main panel board.
this is avoid the high voltage and current. electrical
equipments is softy

Answer / tai s l

HRC stand for high rupturing capacity, use for
1)very hight overcurrent protection normally on top of
motor overload protection devices, act as standby triping,
remmember this : UPS use for back up power failure, triping
aslo must need back up else primaty protection fails leads
to fire and properties damaged
2)high short circuit current with high KA rating compared
with MCCB
3)no moving mechanism once hit fusing current fast acting
to cut of the high fault current flow.. to prevent damage
to the equipment

Answer / ramesh kumar

hrc is a cartridge fuse
link having braking
capacitzy higher than a
certain specified value
[above 16 kv].

Answer / abul hasnat

The primary objection of low and uncertain breaking
capacity of semi enclosed rewireable fuses is overcome in
H.R.C cartridge bridge

Answer / perfect rajasekar

high rucpturing capacity fuse

Answer / abinash nayak

HRC fuse acts as a secondary protective device.It acts if overload relay fails to protect the equipment.

Answer / christy sara vargheese

it means fuse having high capacity to resist the problemes
that occurs in the circut .

Answer / ankaraju.k

It is operated on inverse thermal curret characterstics

How to convert a two phase power into a three phase power in induction machine?

0 Answers  

What are the advantages and disadvantes of delta and star connections in transformers and alternators?

3 Answers  

I am an electrical power engineer and arranged power system for a data center, I installed MCB, ELCB and erthing system TN-C-S. But some times several ELCBs Disconnect circuits at the same time! what may be the reason? (the ELCBs are 25A ,30mA)

9 Answers  

How to resolve if Diesel generator stop while running ?

0 Answers   Toyota,

What are the advantages and disadvantages of open loop control system?

0 Answers  

why any centrifugal blower draw more current in starting. consider id fan and fd fan?

0 Answers  

in single phase we get 220 volt and in three phase 4420 v why this second Ques= in case three phase star conection our neutrul becom disconect what happan 3 Q=== a three phase house load and have unbalce load on different pahse diffrent current eg phase a 7A b 8A c 5A and voltage is 440 than how calculate it total load in kw pl give formula thanks

8 Answers  

I BOUGHT A HAVELLS ACCL WITH GENERATOR STOP FASCILITY(i.e- BASICALLY IT IS A AUTO CHANGE OVER SWITCH) FOR MY HONDA EXK 2000S HOME GENERATOR (WHICH START IN PETROL & RUN IN KEROSENE). ACCL HAS 8 POINT. 2 FOR MAINS(PH & NUE), 2 FOR LOAD, 2 FOR GEN AND 2 FOR IGNITION POINT(X1 & X2). THE IGNITION POINT IS SPECIALLY FOR AUTO ENGINE STOP WHEN MAINS POWER RESTORE. I CONNECT THIS X1 & X2 POINT TO THE GENERATOR STATER MOTOR & EARTHING POINT. BUT WHEN MAINS FAILS THE GENERATOR COULD NOT START, BUT WHEN DISCONNECT THOSE X1 OR X2 POINT, THEN THE GENERATOR START. BUT WHEN MAINS ON THEN THE GENERATOR SHOULD START, AND WHEN I OFF THE MAINS THE GENERATOR AUTOMATICALLY STOP. PLESE HELP ME HOW I STOP THE GENERATOR AUTOMATICALLY WHEN THE MAINS RESTORE.

2 Answers   Honda,

whether choke act as a voltage regulator in tubelight or not?

1 Answers   Bhel,

can a motor acts as a generator

8 Answers   Cummins,

What is capacitance?

0 Answers  

Why motor initial starting current is high?

9 Answers   Pennar,