how to calulate multiplying factor if meter ratio is /5 ampere
and ct ratio is 100/5 ampere.(our supply is 3 phase 415
volts)what is multiply factor?

Answers were Sorted based on User's Feedback



how to calulate multiplying factor if meter ratio is /5 ampere and ct ratio is 100/5 ampere.(our su..

Answer / sandy

if ct ratio is 100/5A then multiplying factor will be 20.

Is This Answer Correct ?    3 Yes 0 No

how to calulate multiplying factor if meter ratio is /5 ampere and ct ratio is 100/5 ampere.(our su..

Answer / dharminder singh

tell me the multiply factor rahul singh

Is This Answer Correct ?    2 Yes 0 No

how to calulate multiplying factor if meter ratio is /5 ampere and ct ratio is 100/5 ampere.(our su..

Answer / rahul singh

M.F= Line CT ration/kwh meter ratio

if kwh meter have /5 ration then you have to install 100 in
pri ration in kwh meter

Is This Answer Correct ?    0 Yes 1 No

Post New Answer

More Electrical Engineering Interview Questions

Can u tell me the name of books of transformer testing?

6 Answers  


If DG runing time Neutral earth connection Dissconect what will be the effect in load and equipments.

3 Answers   GE, HP, Reliance,


what kind of battery is used in laptops

4 Answers   Pepsi,


What will be the fault current of any system when its generation is 10% of BASE generation( FUll Load )?Will is 10% or the same as full base calculation?

0 Answers  


Why consumers are charged based on Kwh basis why not on Kvah basis.

4 Answers   Unitech,






6 MVA transformer secondary is rated for 725V at no load. The incommer ACB is rated at 690 V, 3200 Amp. Would there be any effect on performance of ACB due to lower voltage rating?

5 Answers  


if transformer core is made of copper instead of steel which losses will increase..please explain

5 Answers   Bhel,


how to select earthing wire? procedures and parameters?

2 Answers  


Why shunt Generator is not recommended to start at ON LOAD condition???

3 Answers  


1)What will happen when 240 VDC supply is connected to 240VAC supply(DC supply +ve is connected to phase of AC supply & DC supply is to neutral of AC supply). 2)Also what will happen when 240 VDC supply is connected to 240 VAC supply in reverse polarity as of Sr. No 1.

2 Answers  


what is the harmonics? which harmonics(fundamental and reference) is suitable for calculating capacitor bank and Active filter and passive filter? what is the 1st 2nd 3rd 4th 5th harmonics and effects?

1 Answers  


1) Explain why we don't link the two earthing system ht and mv on a pole mounted transformer sub-station.

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4452)
  • Electrical Engineering Interview Questions Electrical Engineering (16637)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)