i feel sq. pipe is better than round pipe pls give comment for this. advance

i feel sq. pipe is better than round pipe pls give comment
for this.
advance thanks for reply

Question Posted / cvbalan_bhel

3 Answers
5539 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

i feel sq. pipe is better than round pipe pls give comment for this. advance thanks for reply..

Answer / vijay kumar

pressure in round pipe is eqale in all direction but in sq
pipe pressure in all direction is not same that will make
crack on pipe

Is This Answer Correct ?

3 Yes

0 No

i feel sq. pipe is better than round pipe pls give comment for this. advance thanks for reply..

Answer / jazz

pipes are round since pressure is exerted equally in all
directions, all pressure points are equal. if you have a
square pipe, pressure is exerted more on the 90 deg bend for
a square pipe, so since Pressure=Force/Area , you have a
very small area in the bend Force is greatest where you have
a very small cross-sectional area.That point (bend) becomes
a weak point, and becomes a possible leak point.

Is This Answer Correct ?

1 Yes

0 No

i feel sq. pipe is better than round pipe pls give comment for this. advance thanks for reply..

Answer / rakesh kumar .n be

i think in both we can get the center point, because in square all sides have the equal length, like wise in circle they have the equal diameter ,so in both we can get the center point..
* round pipe is always used because at the bending the flow is same,but in square at the bending we can't expect the perfect shape there may be some leak , tat's is the main reason i think so. we can't expect the 100% flow into the pipe, error may be around +or- 10%

Is This Answer Correct ?

1 Yes

2 No

Post New Answer

More Instrumentation Interview Questions

any body who gone thru recent iocl interview.INSTRUMENTATION questions. I need.

0 Answers IOCL,

wHAT IS BURST MODE IN TRANSMITTER?

1 Answers Bhel,

A DP Endress and Hauser flow transmitter is always tripping pump at low flow. set point is 74 cubic meter/hr. Thorough impulse line flushing and zero calibration has been done, yet problem persists. What do you think is the problem and how do you rectify this fault?

5 Answers

1. For Steam drum level signal, why do we compensate with drum pressure signal? 2.For main steam Flow signal is comensated with main steam temperature signal and main steam pressure signal why?

0 Answers

i need some objective type questions in instrumentation

0 Answers

What are the automatic controller MODES?

2 Answers DEWA,

please tell me five types of fault of control valve and positioners?please

1 Answers

What is the main three inputs of DCS?

1 Answers

Why is a dead weight tester so called by that name?

1 Answers SGS,

How can test or measure the probe and extension cable to identify if the problem at the probe or cable or at the driver it self? (pleast notify the measuring method)

0 Answers

1.what is beta in control valves? 2.what is the condition followed by light in LASERs? 3.1kg/cm2=?psi 4.Integral action reduces what? 5.about vena contracta 6.a simple RC circuit 7.thermistor material's temp coefficient of resistance 8.if wave passes through the thicker area of a chord to a thinner area what changes will occur to wavelength? 9.if 4-20 mA represents 0-10 kg/cm2 what will be the current when pressure is 5 kg/cm2.................

0 Answers Lurgi,

DEAR SIR/MADAM MY NAME IS ARKAPROVA BHATTACHARYYA.I AM A FRESHER INSTRUMENTATION ENGINEER.CAN YOU PLEASE SEND SOME QUESTION PAPERS OF GRADUATE ENGINEER TRAINEE EXAM OF DVC(DAMODAR VALLY CORPORATION).MY EMAIL IDs ARE arka_aec@rediffmail.com.

0 Answers

For more Instrumentation Interview Questions Click Here