Interested to Buy Any Domain ? << Click Here >> for more details...
which motor is used in electric train...???????
- 27 Answers
- 61168 Views
- ESPL, IOCL, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / mrityunjoy
dc series motor
reason:- In trains there are many comartments full of
passengers,so during the starting it requires high starting
torque and in dc series motor torque T proportional to Ia
square and Ia=If,so if the motor started without any load
then the armature current will be very high which may
damage the motor.
| Is This Answer Correct ? | 123 Yes | 10 No |
Answer / rajesh.b.jadav
d.c series motor as it has a high starting torque
characteristics
| Is This Answer Correct ? | 84 Yes | 4 No |
kongrates 2 all.. hu said dc series motor.
since the starting torque is very high, obviously this motor
is widely used for traction purposes..
the ratings of komn dc series mtr used for traction is,,
750v dc
650A
the gear ratio is 63:17
each locomotive (train engine)consists 6 such motors.
for more details on this topik kontakt me on mail id
| Is This Answer Correct ? | 45 Yes | 6 No |
Answer / glinto francis
dc series motor becouse high starting torque.this type of
motor is suitable for traction purpose.
| Is This Answer Correct ? | 32 Yes | 2 No |
Answer / sanjay dalvi
Dc series motor is used because it have characteristic of
HIGH STARTING TORQUE IT PICKS UP LOAD WITH CONSTANT SPEED.
| Is This Answer Correct ? | 28 Yes | 3 No |
Answer / ipsa
obviously d.c series motor used in train,hoist,conveyer etc
due to its high starting torque.
| Is This Answer Correct ? | 20 Yes | 1 No |
Answer / k.prakashchandra
Series motor while starting is OK. But how to vary the speed
while running ? Is change over to shunt connection done ?
| Is This Answer Correct ? | 10 Yes | 4 No |
Answer / ramasamyseenu
in the engine side it uses two dc series motor and one 3phase induction motor and the purpose of dc motor is to give high starting current and to make the locomotive to move and to overcome the inertia offered during motion. The purpose of dc series motor is also to perform regenerative braking with 3phase induction motor. The purpose of three phase induction motor is to operate the engine in constant speed.
The motors which are connected below the train compartments are dc series motor it also complements the motion of train from rest thus by reducing load on the train.
| Is This Answer Correct ? | 4 Yes | 1 No |
What is the name of the winding to which supply is given?
apti mainly on logical reasoning, verbal and non-verbal ability (70 percent) and remaining technical. I was in ee but technical had mech ques like on turbines and welding.
how can we calculate the reactence of the current transformers?
What does the kvar means?
how to identyfy cable sizes?
What is meant by pilot exciter and its working?
can you please send me the technical questions and aptitude questions of honeywell and jindal steel electrical engg. question paper my e-mail ID is(kkesavanraj@gmail.com)
How would you supply power to a village which is very far from a sub-station and has only a 11k?
What happen when change order of CT in GIS feeder?
What aturn on methods of scr?
What are the various methods for effecive earthing in a factory in a rocky terrain, where soil resistivity is extraordinarily high? The usual method of 3 m deep earth pits is not serving the purpose.
Transmission lines usually use a.3 phase b.2 phase c. Single phase
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
