Answer / mohamed yousuf(instrumentation

radar type level transmitter works on the principle
of "time of flight system " actually this type of
transmitter having antenna used to send and recive the
micro waves these waves having the frequency range in GHZ.
by calculating the time required to send and recieve the
data the distance can be calculated from the following
expression
velocity=2 distance/time
therefore distance =velocity *time /2

for zero level 4ma and for span 20ma has to set

Answer / vikram kumbhekar

first of all we calculated the total lenth, then set 4mA at
zero level & max lenth at 20mA. When we send a RF freq
signal the time required to recieved the signal,that time
will be calculated by following formula

distance=velocity*time/2

in this way we get the value

Answer / vsraj_ece

radar level txr as a geiger counter and the source is emits
the radio waves into the vessel it contains some liquids the
ionised radio electrons move to the chargable ends as a
measurement unit if low liquids are in vessel means higher
electrons move to measurement unit.

Answer / jamal qamar

Radar level measurement is based on the principle of
measuring the time required for the microwave pulse and its
reflected echo to make a complete return trip between the
non-contacting transducer and the sensed material level.
Then, the transceiver converts this signal electrically into
distance/level and presents it as an analogue and/or digital
signal. The transducer’s output can be selected by the user
to be directly or inversely proportional to the span. RADAR
LEVEL MEASUREMENT BASICS

Ohm’s law, kirchoff’s law, pascal’s law, Bernoulli’s therem,

1 Answers   CCIE, Emcure,

---

In control valve proximity inductive sensor is taken as digital feedback for full open and full close.Normally its volts 24v when the sensor acts the feed back voltage 14v so that our relay not indicating in plc panel . kindly give the solution.

0 Answers  

---

what is compensation in engineering and what is temperature compensation?

1 Answers   Binani, Yokogawa,

---

Please asked me How calculate DCS controller memory.

0 Answers   Yokogawa,

---

Why do we have earthing cable in branch cable and shield in the same cable?

0 Answers   Process Control Technologies,

---

---

what is the relation between flow and pressure.for example relationship between level and pressure is p = phg like that i want ans for this question.and also how to calculate orifice sizing and flow transmitter. pls some one ans for this questions.

3 Answers   Orchid, SRF,

---

tell me the field & lab calibration procedure step by step with diagram of pressure gauge, pressure switch, pressure transmitter, temperature switch, level switch, flow switch, flow transmitter, temperature transmitter, temperature indicator, flow indicator, level indicator, control valve, thermocouple, pressure indicator (digital & analogue),

0 Answers  

---

1. what is 3 point calibration & 5 point calibration? 2. If we use hart communicator to set the LRV & URV of a smart transmitter, did we calibrate the transmitter? why? 3. Make a complet list if meterials needed to properly connect a pressure gauge to a steam pipe using 1/2 inch stainless steel tubing. The gauge connections is 1/2 inch NPT-M and the steam pipe tap has a 1/2 inch female coupling, compression fittings are use. 4. What are the tools in loop checking? 5. What would the ISA symbol of a square root extractor look like? 6. What would you do to completely prepare for the configuration? 7. What safety measures must you undertake when doing configuration? 8. what are the two most commonly use programming languages used when we configure a PLC? 9. What would you do if you accidentally skipped a step in the configuration procedure? 10. How would you know if the configuration were sucessful? 11. Name at least 3 selections available when we configure the burnout protection of a controller?

3 Answers   EI Electrotechnical Institute,

---

How to calibration of vibration probe

1 Answers   Mina Al Ahmadi Refinery,

---

Please any one can provide latest aptitude test,technical test and interview questions for tata consulting engineering (TCE) i need it asap thanks in advance

0 Answers   TCE,

---

What is the difference between Pressure Safety Valve and Pressure Relieve Valve, in what condition we prefer choose Pressure Safety Valve rather than Pressure Relieve Valve? and vice versa

2 Answers   Vedanta,

---

whey we conect ammeter in series and voltmeter in parallel in circuit

1 Answers  

---