why microprocessors are named as 8085 ,8086 etc? what's the reason for thi

Categories >> Engineering >> Electrical Engineering
Suggest New Category

why microprocessors are named as 8085 ,8086 etc?
what's the reason for this???

Question Posted / shyam

15 Answers
45334 Views
Bhel, HCL, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

why microprocessors are named as 8085 ,8086 etc? what's the reason for this???..

Answer / darlateef

80=number of instructions in instruction set of 8085
8=8085 is an 8-bit microprocessor
5=8085 uses single +5V suuply for operation

Is This Answer Correct ?

0 Yes

1 No

why microprocessors are named as 8085 ,8086 etc? what's the reason for this???..

Answer / er ramesh singh

(year)(bits)(supply voltage)
80 8 5 and 8086 in 6 denote the 16 bit register.

Is This Answer Correct ?

2 Yes

5 No

why microprocessors are named as 8085 ,8086 etc? what's the reason for this???..

Answer / harshal

and i want to teach mr. iamdon that
dnt make any statement if u r a dumb
in respective subject. ha!

Is This Answer Correct ?

1 Yes

8 No

why microprocessors are named as 8085 ,8086 etc? what's the reason for this???..

Answer / avanthika

for 8085 as we are using only 5v power supply the last
digit of processor is 5
for 8086 as the width of ALU is 16 the last digit of 16 is
the last digit of microprocessor 8086 ie; 6
for 8088 as it has 8bit bus the last digit of processor is 8

Is This Answer Correct ?

3 Yes

11 No

why microprocessors are named as 8085 ,8086 etc? what's the reason for this???..

Answer / harshal

the first 80 is the specific series . nw,
it has 8 software interrupts and 5
hardware gh intrepts. thats y 85. i
think this will enhance your
knowledge !!

Is This Answer Correct ?

3 Yes

14 No

Post New Answer

More Electrical Engineering Interview Questions

1hp single phase load = howmuch 3 phase load

0 Answers

can we use the 110 v primary Tr 240 v secondary step up Transformer as reverse 240 pri 110 sec

3 Answers Hyundai,

we hav seen in electric engine of trains only 1 wired slidng conecctn is there frm ovrhead line,howevr to complete a ckt in dc postv n negtv two conection has to b there...so where is tht negative is been connectd or where it is grounded...?

5 Answers ABB,

Explain about 3 phase motor fault current calculation with examples?

0 Answers QTC,

I want to measure resistance between Neutro and earth conductor for 3 phase Transformer what should i do

1 Answers

what are the various types of earthing? plz give brief detail of all. also post pictures if u have.

22 Answers Aster Teleservices, Era Infra Engineering, Micron Electricals,

Transformer cores are laminated in order to A simplify its construction B minimize eddy current loss C reduce cost D reduce hysterisis loss

0 Answers

what is the meaning of osr in transformer.

0 Answers

why occ characteristics of generator is also called as magnatization characteristics ?

0 Answers

Hello friends i am facing one problem in lighting panel. Frequently neutral link near to MCCB is burning(firing. What may be the reason for this one. Please answer me.

5 Answers

how to find total current when kva is 30.4 given ? should we use root 3 (1.732) in the formula?

2 Answers

why magnetising curve not start with zero voltage?

0 Answers TATA,

For more Electrical Engineering Interview Questions Click Here