Answer / guest

Thermal plant

Answer / santosh kawade

Most economical power generation is Hydro-power generation,
per unit cost and maintenance cost is very low.

Most easy power generation is wind and solar electricity
power generation.

Santosh Kawade
9224 69 3116

Answer / harsh

installation wise nuclear power plant is most costly but it
reaps long term benifits
when operation and installation both are considered,
thermal power plant is the most efficient

Answer / mayur

i think the question expects the most easiest and economic
way to generate electricity at the already established power
station.So the answer should be HYDRO ELECTRIC POWER STATION.

It must not be thermal,tidal or solar because they are not
available 24/7 or require further treatment on constituent
elements such as heating or conversion.

So go with the HYDRO ELECTRIC POWER STATION.

Answer / prabu

tidal

How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9

0 Answers  

---

If we have 15000kw connected load in a factory than how much power demand sanction should be taken from electricity board. Pls provide complete calculation.

3 Answers  

---

when a cunductor is being disconnected from live cct, still it showing charged, if its checked by line tester?

8 Answers   GEB,

---

The power supplied to a 33microF capacitor from a 120V, 60Hz source will be

0 Answers  

---

hi , i have 150 kw loud and we need 50 m cabil,i want to know wich size cabil we use. thanks

0 Answers  

---

---

what are different types of excitation in synchronous generator,what is the difference between them

3 Answers  

---

What is the function of NGR for the parallel operation of alternator? whats happen when different rating of alternator are running with parallel?

0 Answers   Welspun,

---

What is the selection & Designing procedure for DG/Transformer

4 Answers   Crompton Greaves, Sterling, TATA,

---

which fault is severe and why?between lll fault and lllg fault which fault is severe and y?

0 Answers   GE,

---

What is the procedure/activities to be taken to inject the current more than 2000A by using 2000A Loading Transformer?

0 Answers  

---

what is phase to phase to phase to ground fault

1 Answers  

---

The capacitive reactance of a capacitor of 1/(2(PI)) F at 10^3 H is

0 Answers  

---