Answer / binosh

pressure transmitter:
in bench calibration connect a power supply 24v.give a
250ohms as loop resistance.connect a multimeter in
milliamph mode and connect it in series.and put a
communicator across the loop.the transmitters HP&LP sides
should be in open to atmosphere.this condition the
ammeter shows 4ma and the communicator shows LRV .connect a
pressure calibrator to the HP side and LP keep it open to
atm.apply pressure as the range and go on as 25%,50%,75%and
URV.then the ammeter shows 4,8,12,16,20ma
respectivly.incase you are not getting zero,make zero trim.

Answer / s. kanniyappan

TEMPERATURE TRANSMITTER:
GIVE 24VDC TO THE TRANSMITTER
CONNECT MULTIMETER IN SERIES WITH -VE TO THE TXT
GIVE RESISTANCE INPUT TO THE TRANSMITTER
GIVE LRV VALUE BY ADJUSTING THE DRB
ADJUST ZERO FOR LRV
GIVE URV VALUE BY ADJUSTING THE DRB
ADJUST SPAN FOR URV
GIVE 25%, 50%, 75%, 100% OF URV (RESISTANCE) AND CHECK THE
CORRESPONDING MILLIAMPS OUTPUT

PRESSURE TRANSMITTER:
GIVE 24VDC TO THE TRANSMITTER
CONNECT 250 OHMS IN SERIES WITH -VE TO THE TXT
CONNECT THE HART TO THE TERMINALS OF RESISTANCE
CONNECT THE TRANSMITTER TO THE SOURCE VIA REGULATOR AND MAKE
A T OFF CONNECT TO A MASTER GAUGE
VARY THE PRESSURE BY ADJUSTING THE REGULATOR
MAKE ZERO TRIM FOR ZERO PRESSURE THROUGH HART
ADJUST THE REGULATOR AND CHECK FOR THE LRV VALUE IF NOT
MATCHING ADJUST THE ZERO
DO THE SAME FOR THE URV
GIVE 25%, 50%, 75%, 100% OF URV (PRESSURE) AND CHECK THE
CORRESPONDING MILLIAMPS OUTPUT

DP TYPE TRANSMITTER
LP LINE SHOULD BE LEFT OPEN TO ATMOSPHERE
CONNECT THE HP LINE TO THE SOURCE AND DO THE SAME AS ABOVE

Answer / rajkumar

Any Txr has input, output, supply. give the simulated input
ie.. mA source or mV or pneumatic and check the o/p. if o/p
doesn't match adjust zero or span . Have details of range of
measurements in hand. In need use them also to get desired
output

What is Electrical Runout & Mechanical Runout in Vibration measurement.

1 Answers  

---

Coriolis flow meter coil supply is 24vdc but why still we given 230ac for this transmitter let me explained detailed review please

1 Answers   Shell,

---

What will the new flow factor if D/P Transmitter is RE-RANGED from 25" WC to 50" WC

3 Answers   ADMA OPCO,

---

how many parts of valve positioner?

1 Answers   Kentz,

---

how many mmwc are eual to 1kg/sq.cm & can we calculate mmwc into tph?

2 Answers  

---

How to ensure vibration sensor functioning accordingly.With out using an other sensor.

3 Answers   ACC, Oil India,

---

Hi, I'd like to know the purpose of MOS (maintenance override switch). At site, these switches are installed in a stanchion with the transmitter (connected to ESD). thank you.

3 Answers   Adani, Adani Wilmar,

---

As an industrial instrument technician what we have to know?

3 Answers  

---

How will you calibrate PID controller? explain with example.

0 Answers   Jacobs, Sirte Oil Company,

---

PLS TELL ME THE FUNCTION OR PRINCIPLE OF CREEP RELEIF VALVE..

3 Answers  

---

where i can get training in INTOOLS and PDMS in Delhi-NCR OR north part of India. please reply with ur ans. at arunsamkaria@ymail.com

0 Answers  

---

How to calibrate Magnetic flow Transmitter in Field

0 Answers  

---