why celing fan is running in anti clock wise and table fan
is running in clock wised?
- 5 Answers
- 9792 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / vikas soni
Due to ceiling fan rotor is fixed and table fan stator is
fixed.
| Is This Answer Correct ? | 33 Yes | 9 No |
Answer / hameedullah
Direction of rotation has nothing to do with rotor or
slator. It is the pitch or angle of blades which are
required to run in the required direction (clock or
anticlock wise)for blowing air and not sucking the air. The
direction of any fan or motor can be changed
by "Capicitor's terminals".
| Is This Answer Correct ? | 10 Yes | 5 No |
Dear Friends!..
Try to answer pin point but not to confuse - that person is
asking accurate reason of rotating blades in anticlock or
clock wise if this question is not clear I'm trying to
clear you - u can think in other direction - "why was this
choosen or why is this in fashion to rotate blades of wall
fan / table fan / pedastle fan in clockwise direction where
as ceiling fan exhaust fans in clockwise direction"
Ok! thanks to read my views............
even u cn take it lik a direction to beat your all
interview boards of life - because persons interviewing are
never silly fellows - they know what type of people r in
need for there project and, if u try to misguide them
showing ur over confidence in u - even if u say pardon sir -
u 'll be given chance to answer other questions - because
any employer needs "frank, honest, well wisher, dependable
authentic and eager to learn new things coming in life"
type of people
| Is This Answer Correct ? | 0 Yes | 1 No |
Answer / murugapandiyan
this because of the nature of the air that was flowing. in
out of the blades so that we need air.
| Is This Answer Correct ? | 0 Yes | 2 No |
Answer / draja10
ceiling fan and table fan stator is
fixed.ceiling fan inner stater outer rotor but table fan inner rotor, outer stater so rotating part rotor same two type fan
| Is This Answer Correct ? | 0 Yes | 2 No |
why two contacts(in series) are using in closing circuit
Why does inductive loads consume KVARs?
What_is_mean_by_negative_dc_voltage? why we use -48v except +48v in DC power supply systems.
can u describe the method used for protection of transmission line.
What is nyquist contour?
What is VCB? where it is installed at SP. What is SP?
i need 24v dc from 230v ac supply how we can getit ? what are the devices &its rating requied for that ? plzz i need answer urgently .thank u
What is the selection & Designing procedure for DG/Transformer
4 Answers Crompton Greaves, Sterling, TATA,
hello if any one have papers vof hpcl or sail, plz send me
How Much Capacity of Diesel Genset is suitable for 20 no.s of 1.5ton AC's & Why?(Load Calculation)
11 Answers Lapis Technologies,
which relay is used on long transmission lines
10 Answers ABB, Bhel, Student, Tata Steel Limited,
1. what is the power factor of a purely inductive load? (i) Zero (ii) Lagging (iii)Leading (iv) Unity 2. which type of transformer connection is preferred in case of power supply transformer? (i) Star/Star (ii) Delta/Delta (iii) Star/Delta (iv) Zig Zag/Star
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
