which type signal in & out in dcs

Question Posted / gautam jangra

4 Answers
14749 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

which type signal in & out in dcs..

Answer / rajendra singh

In DCS 4 TYPES OF SIGNAL IS USED

1) AI - ANALOG INPUT THIS FEED BACK SIGNAL FORM (4 - 20 mA)
2) AO - ANALOG OUTPUT COMMAND GIVEN FROM DCS (4 - 20 mA)
3) DI - DIGITAL INPUT (FEED BACK 0 OR 1, HIGH OR LOW)
4) DO - DIGITAL OUTPUT (PICK UP THE RELAY 0 OR 1, HIGH OR
LOW COMMAND GIVEN FROM DCS)

Is This Answer Correct ?

34 Yes

4 No

which type signal in & out in dcs..

Answer / ashish khatana

1) AI - ANALOG INPUT THIS FEED BACK SIGNAL FORM (4 - 20 mA)
2) AO - ANALOG OUTPUT COMMAND GIVEN FROM DCS (4 - 20 mA)
3) DI - DIGITAL INPUT (FEED BACK 0 OR 1, HIGH OR LOW)
4) DO - DIGITAL OUTPUT (PICK UP THE RELAY 0 OR 1, HIGH OR
LOW COMMAND GIVEN FROM DCS)
5) T/C INPUT- FOTR THERMOCOUPLE
6) RTD INPUT- FOR RTD
7) THIRD PARTY COMMUNICATION- LIKE PLC INPUT OUTPUT,
CONTROLLER INPUT OUTPUT (IT IS DIFFERENET FOR DIFFERENT DCS)

Is This Answer Correct ?

17 Yes

2 No

which type signal in & out in dcs..

Answer / khurshidmallick0786@gmail.com

Khurshidmallick0786@gmail.com

Is This Answer Correct ?

0 Yes

0 No

which type signal in & out in dcs..

Answer / farhan

Dcs under stand just 1 to 5 volts therefore 1---5volts enters in it.there is a currernt to volt converter available in dcs.

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Instrumentation Interview Questions

What is motion balance principle?

0 Answers

An electronic p controller has an input range of 1-5v, and output range of 4-20mA, while testing a step change of 0.4 was applied at the input , the PB setting was 50% ,what should be the change in the output ?

1 Answers Reliance,

what is full form of SMART

46 Answers Infosys, ITC Infotech, Lanco, Rosemount, Solvay,

Dear sir I am MD.zafar eqbal. I have taken this id from allinterwiev .com I have qustion if you dont mind. 1.what is the maximum operating temprature in instrumentation. 2. I want know about viberation i mean wahat types of sensor used in viberation And what types of trabsmitter used.and hiw to control it and wher is used of viberation transmitter and finally how to control it and what types of fault come. Sorry for disturbing you. I know you have no reason for help me. Because you dont know about me.but i request you please help me these question are very usefull for my feauture.plz sir Thanking you. Sent from Yahoo! Mail on Android

4 Answers

why the derivative in PID is always set to zero?

3 Answers

what is relation between electronics&instrumentation

4 Answers Hindustan Zinc,

Draw a group of instruments interlocked to a Pump & Motor?

0 Answers

In dissolution apparatus how did you calibrate the distance from end of paddle to bottom of the bowl?

1 Answers Reddy Labs,

What are different types of orifice plates? State their uses.

0 Answers

Related to control system, What is difference between 4-20 mA active & 4-20 mA pasive signal.

1 Answers

Can please tell mi about SIOS, PRM, SERVER, and what is the diference between PIN LAN, PCS LAN,APC Server, and please send the Doc if possible for referance,mail id patil_amit17@yahoo.com

0 Answers

Q1]IF THE RANGE FOR FLOW IS -35 TO 125 WHAT WILL BE THE SPAN FOR ABSOLUTE AND FOR NORMAL? Q2]HOW TO CALIBRATE CAPILLARY TYPE LT? Q3]HOW MANY ERROR CALCULATIONS ARE THERE USED IN PROCESS INDUSTRIES? Q4]HOW TO CALIBRATE TEMPERATURE TRANSMITTER? Q5] HOW TO CALIBRATE LEVEL TROLL AND HOW TO CONNECT? Q6]PLEASE TELL ME THE BASIC FOR INSTRUMENTATION WHICH IS APPLIED FOR CALIBRATION AND FOR ALL? PLEASE MAIL THE ANSWER TO honest_yes@yahoo.in

0 Answers Cegelec, Honeywell,

For more Instrumentation Interview Questions Click Here