If one 10 Hp 3phase induction motor connected in 380volt
50Hz. and again its connected to 380volt 60Hz. howmuch
currrent and power take on both time?????



If one 10 Hp 3phase induction motor connected in 380volt 50Hz. and again its connected to 380volt ..

Answer / badshah

1.2 times that of 50 Hz Power. Frequency increases the
Speed & which in turn increases the power consumption
[P=(2*pi*N*T)/60 and N = 120f/Poles)]..so the ratio is
60/50. But the losses will be more, cause iron & hystersis
losses proportional to frequency squared. I think overall
efficiency may be reduced than when the motor is connected
50 Hz supply.

Is This Answer Correct ?    5 Yes 2 No

Post New Answer

More Electrical Engineering Interview Questions

How can the direction of a three phase induction motor be reserved

4 Answers  


WE HAVE A LOAD OF 55KW MOTOR ITS VOLTS 380 3PH AND ITS TAKING 100AMPS (ITS FULL LOAD IS 105AMPS)AND ITS CABLE IS 4CX50SQMM ,NOW ITS GETTING ABNORMAL HEATUP IN CABLE,PLZ TELL WHY ITS HEAT-UP?(CABLE LENGTH IS 15 METERS ONLY)

10 Answers  


Dear sir, In our plant have Station Transformer having capacity,i want to know, why LV side 40 - 40MVA is given? & how we can get 6.3 KV supply from tertiary(i.e. Open delta connection), Vector Group YNyn0 - yn0 +d MVA Rating 80MVA / 40 - 40MVA + 26.7MVA Voltage rating 420 (Tap range +6,to -10)81.25% /11.5KV - 11.5KV +6.3KV

0 Answers   Bhel,


Electrical Design specifications

1 Answers   Sabic,


can we use inductor for passing or blocking of AC or DC?

3 Answers   Moser Baer, NTPC,






why induction motor always operate at lagging p.f.?

4 Answers  


How o select the electrical fuse?.What are its characteristics.How to select the material od fuse?

0 Answers   BARC,


What is LOP Sensor in DG??????

7 Answers   Emerson,


Alternators are invariably star connected why?

4 Answers  


How would you supply a single house hold load from a 3-phase supply coming out of a sub-station?

4 Answers   Power Grid,


hi this toufik here. i am doing my b.e.degree.now i am in final year and supposed to do a project in this year so i thinking to control the buchholz relay using software base means checking the status of transformer oil using microcontroler, plc or scada. so can i do so...??? alz suggest me...

2 Answers  


In Transmission System if the potential difference at the two end of line are same then is the transmission of power will continue ? if yes then how.

1 Answers   IOCL,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4452)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)