Answer / ponvel

stater is used to protect the motor from overload . if the
starter is 3ph to avoid single phasing and it is used to
redude the startinting current.

Answer / nimish

The function of starter is to reduce the starting current
by inserting initially high resistance. In RLC series
circuit Resistance, inductance and capacitance are
connected in series. If XL is greater than XC then power
factor of circuit is Lagging and if XL is less than XC
power factor is leading. and if XL=Xc then power factor is
unity and this condition is known as resonance.

Answer / ashokreddy r

Function of starter is to limit the starting current and
make the motor start in a desired and safe way.
For dc motor we can go for resistance starters(3-point,4-
point)
For 3phase induction motors we can go for
DOL STARTING ,STAR DELTA STARTING,RESISTANCE STARTING,AUTO
T\F STARTING.

Answer / raj kamal

starter are generally use to reduce the high initial
current to the safer limit. when we start motor, starting
current is usually 6-8 times the full load current. To
reduce this initial rush of current starters are used.
there are various types of starters are as under:
1. DOL STARTER
2. STAR DELTA STARTER
3. REHOSTAT STARTER
4. AUTO TRANSFORMER STARTER

Answer / sk abrahim ali

1.To limit the starting current.
2. To protect the motor from taking overload current,
3.To protect the motor against supply failure,
4.To facilitate the starting and stopping of the motor.

Answer / sabale.dnyaneshwar@gmail.com

The function of starter is to reduce the starting current
which is generally 6 to 7 times of flc. but it is not
reducing the current by inserting resistance. eg. in DOL
starter there is no addition of resistance & it also not
protect the motor from high current. but other starter
i.e star-delta starter. we are reducing the current by
using star connection at the starting.
so, u go in details with starter then u know the each
starter is having diff. operation.
conclusion, by applying various method with starter we are
reducing only starting current.

Answer / ibekwe solomon

A starter is basically used to reduce starting line current
when ever a motor is swicthed on in other to prevent the
coil from burning out because the starting line current is
usually 6times greater than the rated current for motor.

Answer / mostafa karandi

starter includ contol and power circuits and their
equipment such as breakers ,protection elements and
indicators to start a motor in it's best conditon.rlc meter
is an instrument for measuring and testing an electromotor
winding for investigation of motor condition

Answer / anil kumar sharma

stater are using for Control of Moter (on/off) and also using for purpose of safety over current Relay using in starter and also phase preventer relay are using for safety of Motor.

Answer / pratap khamari

a starter is a device generally used to reduce the high
initial current to the safe limit.when we start motors high
initial current to be flow through motors which effect to
others load connected that supply because the initial
current is 6-8 percent of full load current.to reduce the
initial current starters are used except DOL starter.There
are verious type of starter
1.DOL STARTER
2.STAR DELTA STARTER
3.RHEOSTAT STARTER
4.AUTO TRANSFORMER STARTER

what is the equation of converting KW into HP ?

4 Answers  

If we feed 230V ac supply to a full wave rectifare, what & how much will be the out put voltage?

3 Answers  

in a dc shunt motor what happens if motor takes high current,no speed

2 Answers  

For the requirement of a furnace of temperature range up to 1200 oC using silicon carbide rods, What is the required rate of transformer needed (please do it with all details)?

0 Answers   Intel,

Can u tell me the name of books of transformer testing?

6 Answers  

can i use 4 number of circuit breaker as single phase manual change over switch? if yes then how plz also send ckt diagram at nazimzamurad@gmail.com

0 Answers  

how to identify 3phase....r y b .A new make altnator how to identify R

2 Answers  

what is the difference between starter and control panel..?

4 Answers  

WHAT IS A COLOUR CODING OF 3 CORE CABLE

11 Answers  

What is bode plot?

0 Answers  

WHAT SHOULD BE THE BEST CURRENT RATINGS (PRIMARY / SECONDARY)FOR A CT INSTALLED AT THE INCOMING 11KV PANE? WILL IT BE CALCULATED ON THE BASES OF MAXIMUM DEMANT VALUE OR ON SUM OF ALL TRANSFORMER'S KVA? NOMALLY MAX DEMAND REPRESENT THE MAXIMUM OPERATING LOAD OF THE PLANT AND TOTAL KVA OF (SAY 5 NUMBERS TRANSFORMERS) REPRESENT THE CONNECTED LOAD. WHICH i.e. MAX DEMAND KVA OR CONNECTED KVA ARE BETTER TO USE FOR CT CURRENT CALCULATION? PLEASE ANSWER.

0 Answers  

What is the difference between phase, neutral wire and earth cable. if neutral is connected to ground, y we need earthing cable? what difference in hot and cold wire? do neutral wire carry current?

1 Answers