Answer / suresh raajaa

SWITCH FUSE UNIT. IT IS USED FOR PROTECTING POWER AND
CONTROL CIRCUIT DEPENDS ON THE CURRENT RATING REQUIRED.

Answer / rajan

It is Switched Fuse Unit. It has one switch unit and one
fuse unit. When we operate the breaker, the contacts will
get close through switch and then the supply will passes
through the fuse unit to the output.

Whereas in Fuse Switch Unit there is no separte switch and
fuse unit. There is only fuse unit which act itself as a
switch. When we operate the fuse unit will close the input
and output of the breaker.

Answer / vinod

switch fuse unit.there are many protective systems like
HRC,MCCB,MCB...

Answer / karthik

SFU(SWITCH FUSE UNIT)-IT HAS BEEN USED TO TRIP THE
CIRCUIT,PARTICULARLY THIS IS USED FOR HIGH CAPACITY TRIPPING
. WHEREAS MCB&MCCB ARE USED FOR LOW CAPACITY TRIPPING

Answer / ayman

Switch Fuse Unit . It is made of power fuse (80,250,400A)
and switch which can be operated from outside using extend
rotary handle to rotate the shaft which is inside it .

Answer / senindra123

SFU-switch fuse unit. its a fuse unit which can be connet
and disconnect manually with power using a handle.

Answer / sunil kumar rout

sfu -switch fuse unit
it has combination of hrc fuse and a switch unit with different ratting.
when any short ckt hrc fuse is blown and its control ckt and power contactor trip with help of bmr,earth fault relay,ct operated relay,or any type of digital rlay. but in some cases switch unit not trip
it is a old model.
now a days mccb used.

Answer / akhand sharma

Switch fuse unit is a complet unit of controling the power in PCC and MCC panel.. this type of switch using the one of the bigest reson is safety when we work on ground level we can logout or tagout with this switch easily to work...in this unit not only switch it become some of no switch is also connect to control the PCC and MCC panel....at working time......

Answer / vinay

SFU (SWITCH FUSE UNIT) IS USED AS A BASE FOR FUSES IN WHICH
FUSES ARE FIXED IN ELECTRICAL PANELS.

Answer / d r nagar

It is used to protect electrical or electronic devices and
control circuit depending on the current rating.

why we use delta connection in transformer

2 Answers   UPPCL,

1.what type of wave is produced from i.online ups ii.offline ups iii.inverter.why don't we use inverter instant of offline ups for computer,what's the reason?

2 Answers  

how to put cable sizing and cable glands size for respective cable & Cable Lug size in a DB sectors???

0 Answers  

Can u explain : how capacitor act when the supply is given is a.c and d.c. I know that when d.c supply is given then the capacitor charges and becomes open circuited. But please say about when a.c is given. I have seen that when a.c supply is given ,it charges and discharges, But when we plug in capacitor to our daily supply and take it out ,then we join those wires spark will appear,which seems charge is present ,but when a.c is given it should charge and discharge

3 Answers  

how do find power factor in practically and what it means?

3 Answers  

what is the relation bw voltage and F in capacitor?

3 Answers   TATA, Tata Motors,

derive the formula of amp hours is calculated for 12v battery.where no. of plates is given

1 Answers  

with the help of drive can we run the 50hz motor on 100hz,what will be its effect.

3 Answers   BPL,

how much percentage set in transformer diffrencial relay

1 Answers   Bajaj,

if we give 60 hz single phase supply to the transformer used in europe , than what will happen

0 Answers   Core Logic,

1. If 8.35%Z means the percentage impedance of 132kV-line from power company, we will like to reconfirm its base capacity.

0 Answers  

what is the differnce of STATIC ENERGY METER FROM ordinary energy meter?

1 Answers