Answer / phani

first off all u have to learn how to write the question
clearly.
don't use shorcuts
the question must be in clear

Answer / deepakindi1

1)In single phase u measure Voltage wrt neutral ie Phase to
neutral(VN)which is phase voltage,
#In three phase if u measure voltage b/w two line terminals
ie b/w R-y or Y-B or R-B it vl b 440v even in three phase
supply if u measure voltage b/w any phase and neutral point
it vl b 220.(Vph=VL/(square Root of 3).
2)A break in the neutral conductor can however result in
wide rise of the voltages between
each phase and the star point if the three single phase
load currents deviate from the ideal
balanced condition. Depending on the degree of unbalance
between the single phase loads, in
the extreme, the three single phase voltages (phase to
neutral) could vary from as low as zero
volts, to any voltage up to the phase to phase voltage.
Irrespective of load balance, the voltages
between phases are not affected by a break in the neutral
conductor.
3) VR*IR*cos(@)+Vy*Iy*cos(@)+Vb*Ib*cos(@)

Answer / maaz

YOU MUST ASK A QUESTION CLEARLY SO THAT IT CAN BE
UNDERSTOOD TO THE ONE WHO WANTS TO ANWSER IT.
TRY TO GIVE THE QUESTION CLEARLY.

Answer / deepakindi1

Guys nothing wrong in the question though it is in shortcut
but u can understand it.

Answer / deepakindi1

hi ram break means discontinuty or open circuit

Answer / ge hozoor

thanks deepak u givr me answer i use this site frist time
and my dear maaz i try for best thanks ur appriciation

Answer / v_ram

hi deepak....wats the meaning of break in the neutral
conductor.......

Answer / alshaikh

1) the voltage Line to Line is the sum of two phases and these phases have different angles so when we add them respecting to the angle we get vector which is located between the two so, it's drawing is a triangle.

2) If your loads are three phase will not use the neutral and if they are single phase 120 volts they will not work because it is open circui.
3) I am not sure, but I think you can calculate phase power alone then add them together. I think in this case your machine will be damaged because it is unbalanced.

what is the max load on a 10 mva transformer & plz define it with its formula

0 Answers  

Ohm's law applicable for semi-conductors?

4 Answers  

During Testing of Maintenance Free Earthing, How deep should be the Spikes of Earth Test Meter should be inserted in the soil(one spike is 15 Meter & Other spike is 30 Mtrs away from the Main Earth Electrode. Because, recently, we observed that when spike is inserted 3-4 Inch in the earth- results are better, If spike is inserted 1 feet deep than results are increasing.

0 Answers  

How to convert KV into MV in a Transformer?. dont say multification of 1000.pls give practical convertion factor.

2 Answers  

in alternator how we can give power to rotor ? its power is AC or DC ?

5 Answers  

HOW TO CALCULATE THE CAPACITOR RANGE FOR LOAD FOR PF IMPROVEMENT? EXPLE:FOR 65 HP LOAD HOW TO CALCULATE CAPACITOR RANGE?

12 Answers   Al-Malik, All Star Electric, GEC, Reliance, Universal Industries,

Is neutral transformer can be called as control transformer?

0 Answers  

what is stper motor

0 Answers   Bhel, WAPDA Water and Power Development Authority,

what is deffrence between squirral cage and wound rotor in IM?

0 Answers   ME,

Hi, We have have the major losses between BBT ( Bus Bar Trunking) to LT Incomer & LT to HT incomer, how to arrive the losses?

1 Answers  

A 6.6 KV motor breaker is try to Drack OUT by me while the motor running. What will Happened? a, will Trip. b,Drack Out lever will not access c, will get shock d, noting will happened

4 Answers  

Why DC excitation is used for alternators? Why cant it be AC?

35 Answers   ABB, Ace Info, Alstom, Shalivahana Power,